Marble Wax Polishing Floor Wax Polishing in Delhi NCR
Wax polishing gives a quick, warm sheen on stone, mosaic and tile floors, and it is the right finish where a hard crystallised surface would be too slippery or too expensive to maintain. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Free inspection of surface and existing coating
- Stripping of old wax and residue
- Floor cleaned and fully dried before waxing
- Two thin coats applied and buffed
At a glance
- 12 years experience
- 600+ projects a year
- Written rates
A real before and after photo is added here for the strongest result.
What is included in marble wax polishing
- Floor cleaned and fully dried before waxing
- Two thin coats applied and buffed
- Even coverage across lanes and corners
- Edge and skirting hand finishing
- Walkway protection until dry
- Maintenance schedule explained
- Free inspection of surface and existing coating
- Stripping of old wax and residue
What each surface needs
| Surface | Why wax suits it | Result |
|---|---|---|
| Mosaic and terrazzo | Adds sheen without hardening | Warm even gloss |
| Kota and cement floors | Cheap to renew each cycle | Uniform matte to gloss |
| Ceramic and tile | Slip-friendly finish | Clean sheen |
| Stone needing a soft finish | No crystallisation haze | Soft reflective look |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and coating test (free)
- Stripping of old wax and dirt
- Cleaning and drying
- Two thin wax coats with buffing
- Handover with a re-wax schedule
Marble Wax Polishing rates in Delhi NCR
| Work | Guide band | Notes |
|---|---|---|
| Strip and re-wax | Rs 5-15 per sq ft | Most floors |
| Deep clean plus wax | Rs 15-25 per sq ft | Heavy build-up |
| Buff only | Rs 5-10 per sq ft | Maintenance cycle |
| Slip-control finish | Quoted after inspection | Wet areas |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
The process, step by step
- Site inspection, gloss reading and hidden test patch
- Masking of skirting, fittings, doors and furniture edges
- Residue and old polish stripping where present
- Grinding if lippage or deep damage is found
- Progressive polishing through the grit sequence
- Optional silicate, crystallisation, epoxy or nano finish
- Edge and corner hand work
- Wash-down, walkthrough and care guidance
Each stage is completed on the whole area before the next one starts, so the floor never ends up with a bright patch next to an unfinished section.
Where a floor has mixed surfaces, each one gets its own pad sequence and compound. Treating Kota stone and imported marble with the same approach is how floors get patchy.
The written rate is the final amount for the agreed scope. If we open the floor and find something the inspection could not show, we stop and re-quote with you before continuing, not after.
Why clients book us
- Old wax fully stripped, never layered over dirt
- Two thin coats instead of one thick coat
- Honest advice when wax is the wrong finish
- Re-wax cycles planned around your traffic
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Wax Polishing - common questions
Does wax damage stone?
Not if it is stripped and reapplied properly. Wax left to build up for years traps grit that then scratches the stone underneath, which is the real problem.
Is wax better than crystallisation?
They suit different floors. Crystallisation hardens marble for heavy traffic; wax gives an even sheen on mosaic, Kota and cement floors where hardening would be too aggressive.
Can wax reduce slipperiness?
A waxed surface is less mirror-smooth than a crystallised one, which helps in some areas, but for bathrooms and staircases we recommend a proper anti-skid treatment.
How long does a wax finish last?
Six to twelve weeks in high-traffic areas and three to six months in homes, depending on mopping and footfall. It is renewable, which is why some commercial floors use wax on purpose.
How long does each step take?
As a guide, preparation is under an hour, grinding runs 25-40 minutes per 100 sq ft, polishing 15-25 minutes, and finishing plus clean-up about an hour. Bigger areas are scheduled over more days.
Can steps be skipped to save money?
Not safely. Skipping grit stages is the most common shortcut and shows up as scratch haze within weeks. If you want to reduce cost, reduce the area covered this cycle, not the process.
Do you work in one room or the whole floor at a time?
Room by room if you are living in, whole floor if the house is empty, which produces a more even finish because lighting and drying are consistent.