Floor Polishing Services in Bangalore
Marble, granite, tile, terrazzo and wooden floors all dull for different reasons, and treating them with the same machine and pads is how floors get damaged. We identify the surface first, then use the sequence that suits it. Bangalore is granite country, so most homes mix granite platforms and staircases with marble or vitrified floors. Hard borewell water leaves scale and white film on stone, which is why descaling is usually part of the job here.
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
- Coarse diamond passes for scratches and lippage
- Progressive grits to remove every previous scratch pattern
At a glance
- One team, all surfaces
- Written rates
- Klindex & Taski
A real before and after photo is added here for the strongest result.
What is included in floor polishing
- Coarse diamond passes for scratches and lippage
- Progressive grits to remove every previous scratch pattern
- Fine polishing to bring up the working gloss
- Edge and corner work by hand machine
- Optional crystallisation or nano finish
- Floor washed and handed over with a gloss check
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
What each surface needs
| Grit | What it does | When it is needed |
|---|---|---|
| 60 and 100 | Cuts back lippage, deep scratches and rough patches | Uneven joints, heavy damage |
| 200 and 400 | Removes grinding marks, levels the surface | After any coarse stage |
| 800 | Closes the pores and prepares the stone | Almost every job |
| 1500 and 3000 | Working gloss and final mirror pass | Homes, lobbies, showrooms |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free, 20 minutes)
- Masking of all surfaces that should not get slurry
- Sequential diamond passes, 30-45 minutes per 100 sq ft
- Finishing pass at 1500 or 3000 grit, coating if you approve
- Handover with before and after gloss comparison
Floor Polishing rates in Bangalore
| Work | Guide band | Where it applies |
|---|---|---|
| Light diamond pass | Rs 5-15 per sq ft | Sound floors, mild dulling |
| Standard diamond polishing | Rs 15-25 per sq ft | Scratch lanes, worn gloss |
| Deep diamond plus crystallisation | Rs 25-35 per sq ft | Lippage, stains, heavy wear |
| Coating after polishing | Quoted after inspection | Silicate, epoxy or nano |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
What changes the price for floor polishing in Bangalore
| Factor | Effect on rate | What to expect |
|---|---|---|
| Total area | Bigger areas cost less per sq ft | Slab rates above 1,000 sq ft |
| Damage depth | Grinding raises the rate | Decided by the test patch |
| Stone type | Imported and filled slabs take longer | See the surface table |
| Access | Upper floors and corners take longer | Confirmed before booking |
Ask for one written rate per surface. A single number for the whole house without an inspection always changes later.
The problems we are usually called for
| Problem | What causes it | Fix |
|---|---|---|
| Overall dullness | Worn finish, cleaning residue | Strip and re-polish |
| Scratch lanes | Grit walked in from entrances | Diamond polish those lanes |
| Grey or black patches | Water trapped, old polish build-up | Grind, dry, polish, seal |
| White watermark rings | Planters, metal legs, spills | Poultice and re-polish |
| Loose or black joints | Failed grouting, water ingress | Cut out and re-point |
| Slippery when wet | Gloss in a wet area | Satin finish plus anti-skid |
Send a photo of the worst patch on WhatsApp and we will tell you which of these it is before anyone visits.
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Machines are matched to the job. A 400 mm single-disc machine for open floors, edge machines for skirtings and staircases, and hand blocks for corners and thresholds where a machine cannot safely reach.
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
Why clients book us
- 12 years, 600+ floor projects a year
- Fresh diamond segments, because worn pads leave swirl marks
- Correct pad set per stone: marble, granite, Kota, terrazzo
- One contractor for grinding, polishing and coatings
Serving Bangalore and nearby areas
Bangalore visits are planned as a batch with machines brought in, so work is booked in advance rather than as same-day calls. Bangalore is granite country, so most homes mix granite platforms and staircases with marble or vitrified floors. Hard borewell water leaves scale and white film on stone, which is why descaling is usually part of the job here. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Floor Polishing - common questions
How is diamond polishing different from the polish my housekeeping does?
Housekeeping applies cream or wax that sits on the surface and wears off in walking lanes within weeks. Diamond polishing refines the stone itself, so the finish is part of the floor.
How much marble does it remove?
Microns, not visible layers. Even a full sequence on a damaged floor only corrects the worn top surface; coarse grinding is the stage that removes more and we only use it when needed.
How glossy will the floor look?
Most marble reaches a near-mirror gloss. Statuario and Makrana take a very high gloss, while honed travertine and some Kota floors look better satin. We agree the target before starting.
How long does the finish last?
Two to three years in homes before a light maintenance pass; eight to twelve months in offices and hotels, longer with a silicate or nano coating.
Can it be done in an occupied home?
Yes. The process is wet, so dust stays low. We work room by room and leave dry paths so you can stay in the house.
Is the price negotiable?
The rate per sq ft is not inflated to leave room for haggling. We scope honestly: if the floor needs only a buff, we quote a buff instead of a full diamond job, and tell you when the cheaper option will hold.
Do you take advance payment?
The package is confirmed in writing first. Advance for material is normal on large jobs; the balance is settled after the walkthrough.
Which of these can you fix in one visit?
Dullness, scratch lanes, watermark rings and slippery surfaces are usually single-visit jobs. Trapped water, loose joints and cracked or hollow slabs may need a second visit because of drying or re-pointing time.
What if the damage is worse than the photos showed?
We stop and re-quote rather than continuing on a guess. You approve the revised scope or we finish what was agreed and leave the rest.
Can repeated problems be prevented?
Most of them, yes. Entrance mats, pH-neutral cleaning, felt pads and prompt spill wipe-up remove the four causes behind the majority of callbacks.