Marble Installation and Fitting in Punjab
We lay, level and finish marble so the joints are tight, the surface is flat and the polish takes evenly. Bad fitting is what forces grinding later, and that costs more than doing it right. Work in Punjab is planned as a scheduled visit: the crew and machines travel together on a fixed date, and the rate is written down after the floor is seen in person or from clear photos.
- Free inspection and test patch
- Masking of walls, skirting and furniture edges
- Wet sanding through the grit sequence
- Slurry vacuumed as work proceeds
At a glance
- 12 years experience
- 600+ projects a year
- Written rates
A real before and after photo is added here for the strongest result.
What is included in marble installation
- Masking of walls, skirting and furniture edges
- Wet sanding through the grit sequence
- Slurry vacuumed as work proceeds
- Damage and joint treatment where found
- Polishing after sanding on request
- Wash-down of the whole area
- Care advice for the first week
- Free inspection and test patch
What each surface needs
| Problem | Wet sanding effect | Outcome |
|---|---|---|
| Grey mop haze | Strips the residue layer | True stone colour returns |
| Old wax and coatings | Fully removed | Surface ready for polish |
| Light scratches | Ground out in stages | Even surface |
| Paint, POP and cement spots | Removed without acid | Clean stone |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free)
- Masking and water containment
- Wet sanding in grit stages
- Slurry vacuumed and area washed
- Handover with finish options
Marble Installation rates in Punjab
| Work | Guide band | Notes |
|---|---|---|
| Wet sanding only | Rs 5-15 per sq ft | Residue removal |
| Wet sanding plus polishing | Rs 15-25 per sq ft | Dull floors |
| Sanding, grinding and polish | Rs 25-35 per sq ft | Damage and lippage |
| Coating after sanding | Quoted after inspection | Protection |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Reading a per sq ft quote correctly
- Ask whether grinding is included or quoted separately, because that is the single biggest swing in the number
- Ask what the rate excludes: coatings, crack filling, slab replacement and waste removal are the usual extras
- Check whether the area is charged on carpet area or built-up area, and whether staircases are priced per step
- Confirm the rate applies to the measured floor, not an estimate from photographs
- Insist on one written figure per surface where floors are mixed
| Rate band | Typical work included |
|---|---|
| Lowest band | Maintenance buff on a sound floor |
| Middle band | Diamond polishing, scratch and lane correction |
| Upper band | Grinding, deep correction, crystallisation or coating |
Two quotes can differ by 40 percent for the same floor simply because one includes grinding and the other does not. Compare the scope, not just the number.
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Machines are matched to the job. A 400 mm single-disc machine for open floors, edge machines for skirtings and staircases, and hand blocks for corners and thresholds where a machine cannot safely reach.
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
Why clients book us
- Slurry contained and vacuumed, not left to dry
- Test patch shown before the full job
- One team for sanding, grinding and polishing
- 12 years of marble work
Serving Punjab and nearby areas
Punjab jobs are booked as a fixed visit batch, so travel is planned into the date instead of being added as a surprise. Work in Punjab is planned as a scheduled visit: the crew and machines travel together on a fixed date, and the rate is written down after the floor is seen in person or from clear photos. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Installation - common questions
Does wet sanding remove a lot of stone?
It removes the coating and the damaged top layer only. Deep lippage needs grinding first, which we identify during inspection.
How messy is it?
We mask surfaces and vacuum slurry as we work, then wash the area before handover. Your furniture and curtains do not end up coated in dust.
Can it be done room by room?
Yes. Most clients do one or two rooms at a time, and dry paths are kept so the house stays usable.
Why wet sanding instead of dry?
Because dust control matters in occupied homes. Water carries the residue away and keeps the surface cool, which protects the stone from heat marks.
Why do per sq ft rates differ so much between contractors?
Almost always scope. A rate that excludes grinding, crack filling and coatings looks cheaper until those are added. Ask for the scope in writing and compare the total, not the headline rate.
Is the rate cheaper for larger areas?
Yes. Above roughly 1,000 sq ft we move to slab rates because setup and travel are spread over more work.
How do you measure the area?
On site, with you present, room by room. You see the measurement sheet before the quote is finalised.