Marble Floor Scratch Removing in Delhi NCR
Marble, granite, tile, terrazzo and wooden floors all dull for different reasons, and treating them with the same machine and pads is how floors get damaged. We identify the surface first, then use the sequence that suits it. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Free inspection measuring lippage and slab thickness
- Tapping test for hollow slabs
- Wet grinding to keep dust down indoors
- Coarse to fine grit sequence with no skipped stages
At a glance
- One team, all surfaces
- Written rates
- Klindex & Taski
A real before and after photo is added here for the strongest result.
What is included in marble floor scratch removing service
- Free inspection measuring lippage and slab thickness
- Tapping test for hollow slabs
- Wet grinding to keep dust down indoors
- Coarse to fine grit sequence with no skipped stages
- Slurry contained and vacuumed as we work
- Refining passes to remove grind marks
- Polishing to follow on the same job
- Wash-down and walkthrough
What each surface needs
| Problem | What grinding does | Outcome |
|---|---|---|
| Lippage between slabs | Cuts the high slab to floor level | Flat floor, no trip lines |
| Dark traffic lanes | Removes the compacted worn layer | Uniform colour across the room |
| Deep scratches and gouges | Cuts back below the scratch depth | Gone, or faint on very deep damage |
| Cement, POP and paint splatter | Removes it without acid | Clean stone, no chemical risk |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection, lippage measurement and hollow test (free)
- Masking of walls, skirting, doors and furniture
- Coarse grinding, 40-60 minutes per 100 sq ft
- Refining at 200 and 400 grit, 30-45 minutes per 100 sq ft
- Polishing, wash-down and handover
Marble Floor Scratch Removing Service rates in Delhi NCR
| Work | Guide band | Typical case |
|---|---|---|
| Light grinding with polish | Rs 15-25 per sq ft | Surface damage, patchy gloss |
| Full grinding, levelling and polish | Rs 25-35 per sq ft | Lippage, deep damage, dark lanes |
| Crystallisation after grinding | Quoted after inspection | Adds hardness and gloss |
| Grinding plus slab re-laying | Quoted per slab | Hollow or lifted slabs |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Booking a crew near you
- Crews operate from two bases, so most addresses in the service cities are reached the same day for inspection
- Inspections are booked within 24-48 hours, and one-day jobs are often scheduled within the same week
- Society gate, lift and parking permissions are arranged before the crew arrives
- Machines, water supply and power needs are confirmed at booking, so nothing delays the start
- Local route days keep travel short, which keeps the per sq ft rate down
If your address is outside the listed service cities, ask before booking. We tell you honestly whether we can cover it, instead of sending a crew that bills travel into the job.
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Machines are matched to the job. A 400 mm single-disc machine for open floors, edge machines for skirtings and staircases, and hand blocks for corners and thresholds where a machine cannot safely reach.
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
Why clients book us
- 12 years of stone grinding in Delhi NCR
- Slab thickness checked before we agree to grind
- Wet grinding with slurry contained and the site washed down
- Same team polishes after grinding, so nothing is blamed on another contractor
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Scratch Removing Service - common questions
Does grinding create dust all over the house?
We grind wet, so dust becomes slurry rather than airborne powder, and we mask doors and skirting. Slurry is vacuumed and washed before we leave.
Can lippage between marble and tile be levelled?
Usually yes where the two surfaces meet at different heights. Where the step is more than a few millimetres, an exact match may not be possible and we say so before starting.
Is grinding always followed by polishing?
Yes in practice. Grinding leaves machine marks until the finer grits and polishing smooth them out, which is why the two stages are quoted together.
What if a slab is hollow?
Grinding cannot re-bond it. Loose slabs must be re-laid, and we quote that separately rather than hiding the problem under a polish.
Will grinding make my floor noticeably thinner?
It removes a fraction of a millimetre at the surface and more only where slabs are high. Average floors take several grinding cycles over their life. We measure thickness during the free inspection first.
How soon can someone come for an inspection?
Usually within 24-48 hours in our service cities. If you are on a route day, it can be the same day.
Do you cover my area?
Send the locality or PIN code and we will confirm. We would rather decline a job than travel from far and load that cost onto your rate.
Can the work be done on a weekend?
Yes. Weekend and after-hours slots are normal for occupied homes and commercial premises.