Marble Floor Polishing in West Port
If your marble has lost its gloss, shows grey walking lanes or looks hazy after mopping, the finish has worn through to the stone. We restore it with a graded diamond sequence and lock the shine in, so the floor holds its look instead of going flat again in a few weeks. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Gloss and polish-condition check first
- Masking of skirting, walls and fittings
- Diamond polishing to the grit the treatment needs
- Even section-by-section silicate application
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Masking of skirting, walls and fittings
- Diamond polishing to the grit the treatment needs
- Even section-by-section silicate application
- Machine buffing to remove residue and streaks
- Edge and corner treatment by hand
- Walkway protection until the surface sets
- Cleaning advice so acid cleaners never touch it
- Gloss and polish-condition check first
What each surface needs
| Treatment | Character | Best for |
|---|---|---|
| Sil200 | Fast build, strong initial gloss | Homes and moderate traffic |
| Sil800 | Deeper wet look, holds gloss longer | Lobbies, showrooms, hotels |
| Over new stone | Protects an unworn surface | Recently laid or newly polished floors |
| Over worn stone | Short-lived unless polished first | Only after a full diamond sequence |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Assessment to confirm silicate suits the stone and the room
- Diamond polishing to 800-1500 grit so there is a finish worth locking in
- Silicate applied in sections and buffed while it reacts
- Second pass on heavy areas for even gloss
- Gloss check and a list of cleaners to avoid
Marble Floor Polishing rates in Kolkata
| Work | Guide band | Notes |
|---|---|---|
| Polish plus Sil200 | Rs 15-25 per sq ft | Homes, standard traffic |
| Polish plus Sil800 | Rs 25-35 per sq ft | Lobbies, hotels, heavy traffic |
| Silicate over an already polished floor | Quoted after inspection | Floor must still be sound |
| Repeat maintenance treatment | Quoted after inspection | Every 1-3 years |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving West Port
Marble Floor Polishing in West Port is handled on scheduled routes by our Kolkata team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for West Port addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own West Port job handed over for your records
Night, weekend and occupied-premises work
- Evening, night and Sunday slots so trading hours and office shifts are untouched
- Machine noise managed around residents, guests and neighbours, with work sequenced floor by floor
- Zones handed back ready for use before the next shift or opening time
- Lighting provided where a site has no working lights after hours
- Supervisor present throughout, with one point of contact for the site manager
Working after hours costs a little more in crew arrangements, and we tell you that upfront rather than burying it in the rate.
Waste is removed the same day. Slurry, stripped residue, used pads and packaging leave with the crew instead of going into society bins or being left for you to dispose of.
Nothing is hidden behind a shine. Where a surface has damage that polishing cannot correct, we mark it during inspection and put it in writing, so expectations are set before work starts rather than argued over afterwards.
After-care guidance is handed over in writing: which cleaner to use, how to mop, and what to avoid during the first week. Most repeat problems trace back to cleaning products rather than the work itself.
Why clients book us
- Product chosen for the stone, not one bottle for all
- Residue buffed off before handover
- 12 years of stone finishing
- We polish before we treat, never over a dull surface
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
How long does it last?
Roughly two to three years in homes and one to two years in heavy-footfall lobbies. Using a pH-neutral cleaner instead of acid is the biggest factor.
Can it be applied to a floor that was never polished?
It can, but it is rarely worth it, because silicate amplifies whatever surface it meets and locks in scratches. We polish to 800-1500 grit first or refuse the treatment.
Will it make the floor slippery?
A high-gloss finish is smoother when wet. In bathrooms, kitchens and on staircases we recommend a satin or crystallised finish instead of mirror gloss.
How long before we can walk on it?
The floor is walkable the same evening. Only normal drying after the polishing stage is needed, with no curing days.
Is silicate the same as waxing the floor?
No. Wax sits on the surface and wipes off. Silicate reacts with the calcium in the marble and hardens the surface layer, so the gloss is part of the stone and survives mopping.
Do you cover West Port?
Yes. West Port is on our regular route with the Kolkata team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in West Port?
Inspection first, then scheduling. Most West Port jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
Is there a premium for night work?
Sometimes, and we say so before booking. It covers crew scheduling and transport at unsociable hours, not the work itself.
Can you work while our premises stay open?
Yes. Work is phased section by section, with dry paths and signage so customers and staff are never crossing a wet or machine-worked area.
Will the machines disturb neighbours?
Machine noise is unavoidable for short periods. We sequence the noisiest work earlier, and for residential buildings we stay within the society's permitted hours.