Marble Floor Polishing in Paddapukur
If your marble has lost its gloss, shows grey walking lanes or looks hazy after mopping, the finish has worn through to the stone. We restore it with a graded diamond sequence and lock the shine in, so the floor holds its look instead of going flat again in a few weeks. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
- Coarse diamond passes for scratches and lippage
- Progressive grits to remove every previous scratch pattern
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Progressive grits to remove every previous scratch pattern
- Fine polishing to bring up the working gloss
- Edge and corner work by hand machine
- Optional crystallisation or nano finish
- Floor washed and handed over with a gloss check
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
- Coarse diamond passes for scratches and lippage
What each surface needs
| Grit | What it does | When it is needed |
|---|---|---|
| 60 and 100 | Cuts back lippage, deep scratches and rough patches | Uneven joints, heavy damage |
| 200 and 400 | Removes grinding marks, levels the surface | After any coarse stage |
| 800 | Closes the pores and prepares the stone | Almost every job |
| 1500 and 3000 | Working gloss and final mirror pass | Homes, lobbies, showrooms |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free, 20 minutes)
- Masking of all surfaces that should not get slurry
- Sequential diamond passes, 30-45 minutes per 100 sq ft
- Finishing pass at 1500 or 3000 grit, coating if you approve
- Handover with before and after gloss comparison
Marble Floor Polishing rates in Kolkata
| Work | Guide band | Where it applies |
|---|---|---|
| Light diamond pass | Rs 5-15 per sq ft | Sound floors, mild dulling |
| Standard diamond polishing | Rs 15-25 per sq ft | Scratch lanes, worn gloss |
| Deep diamond plus crystallisation | Rs 25-35 per sq ft | Lippage, stains, heavy wear |
| Coating after polishing | Quoted after inspection | Silicate, epoxy or nano |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving Paddapukur
Marble Floor Polishing in Paddapukur is handled on scheduled routes by our Kolkata team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for Paddapukur addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own Paddapukur job handed over for your records
Night, weekend and occupied-premises work
- Evening, night and Sunday slots so trading hours and office shifts are untouched
- Machine noise managed around residents, guests and neighbours, with work sequenced floor by floor
- Zones handed back ready for use before the next shift or opening time
- Lighting provided where a site has no working lights after hours
- Supervisor present throughout, with one point of contact for the site manager
Working after hours costs a little more in crew arrangements, and we tell you that upfront rather than burying it in the rate.
Quotes are itemised per surface rather than as one lump sum, so a mixed floor of marble, tile and stone is priced line by line and you can approve, defer or drop any line.
The written rate is the final amount for the agreed scope. If we open the floor and find something the inspection could not show, we stop and re-quote with you before continuing, not after.
Machines are matched to the job. A 400 mm single-disc machine for open floors, edge machines for skirtings and staircases, and hand blocks for corners and thresholds where a machine cannot safely reach.
Why clients book us
- Fresh diamond segments, because worn pads leave swirl marks
- Correct pad set per stone: marble, granite, Kota, terrazzo
- One contractor for grinding, polishing and coatings
- Gloss checked with you before the crew leaves
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
How much marble does it remove?
Microns, not visible layers. Even a full sequence on a damaged floor only corrects the worn top surface; coarse grinding is the stage that removes more and we only use it when needed.
How glossy will the floor look?
Most marble reaches a near-mirror gloss. Statuario and Makrana take a very high gloss, while honed travertine and some Kota floors look better satin. We agree the target before starting.
How long does the finish last?
Two to three years in homes before a light maintenance pass; eight to twelve months in offices and hotels, longer with a silicate or nano coating.
Can it be done in an occupied home?
Yes. The process is wet, so dust stays low. We work room by room and leave dry paths so you can stay in the house.
How is diamond polishing different from the polish my housekeeping does?
Housekeeping applies cream or wax that sits on the surface and wears off in walking lanes within weeks. Diamond polishing refines the stone itself, so the finish is part of the floor.
Do you cover Paddapukur?
Yes. Paddapukur is on our regular route with the Kolkata team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in Paddapukur?
Inspection first, then scheduling. Most Paddapukur jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
Is there a premium for night work?
Sometimes, and we say so before booking. It covers crew scheduling and transport at unsociable hours, not the work itself.
Can you work while our premises stay open?
Yes. Work is phased section by section, with dry paths and signage so customers and staff are never crossing a wet or machine-worked area.
Will the machines disturb neighbours?
Machine noise is unavoidable for short periods. We sequence the noisiest work earlier, and for residential buildings we stay within the society's permitted hours.