Marble Floor Polishing in Narkeldanga
If your marble has lost its gloss, shows grey walking lanes or looks hazy after mopping, the finish has worn through to the stone. We restore it with a graded diamond sequence and lock the shine in, so the floor holds its look instead of going flat again in a few weeks. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Free inspection and test patch
- Masking of walls, skirting and furniture edges
- Wet sanding through the grit sequence
- Slurry vacuumed as work proceeds
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Free inspection and test patch
- Masking of walls, skirting and furniture edges
- Wet sanding through the grit sequence
- Slurry vacuumed as work proceeds
- Damage and joint treatment where found
- Polishing after sanding on request
- Wash-down of the whole area
- Care advice for the first week
What each surface needs
| Problem | Wet sanding effect | Outcome |
|---|---|---|
| Grey mop haze | Strips the residue layer | True stone colour returns |
| Old wax and coatings | Fully removed | Surface ready for polish |
| Light scratches | Ground out in stages | Even surface |
| Paint, POP and cement spots | Removed without acid | Clean stone |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free)
- Masking and water containment
- Wet sanding in grit stages
- Slurry vacuumed and area washed
- Handover with finish options
Marble Floor Polishing rates in Kolkata
| Work | Guide band | Notes |
|---|---|---|
| Wet sanding only | Rs 5-15 per sq ft | Residue removal |
| Wet sanding plus polishing | Rs 15-25 per sq ft | Dull floors |
| Sanding, grinding and polish | Rs 25-35 per sq ft | Damage and lippage |
| Coating after sanding | Quoted after inspection | Protection |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving Narkeldanga
Marble Floor Polishing in Narkeldanga is handled on scheduled routes by our Kolkata team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for Narkeldanga addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own Narkeldanga job handed over for your records
Buff or full polish? A straight answer
| Condition of the floor | Correct job | Why |
|---|---|---|
| Dull but even, no scratches | Buff only | Surface is sound, only the sheen is lost |
| Light scratches and lane wear | Diamond polish | Surface layer needs refining |
| Visible lippage or deep scratches | Grinding plus polish | Buffing cannot level stone |
| Wax or polish residue build-up | Strip, then polish | New finish will not bond over residue |
Buffing is the cheaper option and we will tell you when it is enough. Selling a full polish for a floor that only needed a buff is how a contractor gets a bad name.
Access is confirmed before the visit: parking, lift use, gate entry, working-hour restrictions and any society paperwork. Sorting this in advance is what stops a scheduled job from becoming a wasted trip.
Old polish, wax and cleaning residue are stripped before any new finish goes on. Layering a fresh treatment over residue is what makes floors look grey again within weeks.
Water and power are the two site requirements. We need one working socket within reach of a lead and a water point; everything else, including masking material and waste bags, comes with the crew.
Why clients book us
- Slurry contained and vacuumed, not left to dry
- Test patch shown before the full job
- One team for sanding, grinding and polishing
- 12 years of marble work
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
Does wet sanding remove a lot of stone?
It removes the coating and the damaged top layer only. Deep lippage needs grinding first, which we identify during inspection.
How messy is it?
We mask surfaces and vacuum slurry as we work, then wash the area before handover. Your furniture and curtains do not end up coated in dust.
Can it be done room by room?
Yes. Most clients do one or two rooms at a time, and dry paths are kept so the house stays usable.
Why wet sanding instead of dry?
Because dust control matters in occupied homes. Water carries the residue away and keeps the surface cool, which protects the stone from heat marks.
Do you cover Narkeldanga?
Yes. Narkeldanga is on our regular route with the Kolkata team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in Narkeldanga?
Inspection first, then scheduling. Most Narkeldanga jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
How do I know if buffing is enough?
If the floor is evenly dull with no visible scratch pattern, a buff usually restores it. If you can see lanes, scratches or a step between slabs, it needs polishing or grinding, and we show you why on a test patch.
Is buffing a waste of money then?
Not at all. It is the correct maintenance step for a sound floor and costs a fraction of a full job. It becomes a waste only when the surface damage needs something deeper.
Can you do a test patch first?
Yes, on every job. One tile or a corner, so you judge the actual result before committing to the whole floor.