Marble Floor Polishing in Liluah
If your marble has lost its gloss, shows grey walking lanes or looks hazy after mopping, the finish has worn through to the stone. We restore it with a graded diamond sequence and lock the shine in, so the floor holds its look instead of going flat again in a few weeks. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Free inspection including slab-thickness and hollow check
- Masking and furniture protection
- Grinding where lippage or deep scratches exist
- Graded diamond polishing to the stone hardness
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Graded diamond polishing to the stone hardness
- Old polish and wax residue removal
- Stain treatment for oil, rust and hard water
- Silicate or crystallisation option
- Wash-down and walkthrough
- Free inspection including slab-thickness and hollow check
- Masking and furniture protection
- Grinding where lippage or deep scratches exist
What each surface needs
| Stone | Hardness | Best finish |
|---|---|---|
| Makrana white | Medium-hard, takes high gloss | Mirror gloss |
| Katni and Jaisalmer | Softer, colour sensitive | Satin to medium gloss |
| Rajnagar and green marble | Hard, banded | Gloss with even banding |
| Kota and other flagstone | Hard, matte by nature | Densified gloss or matte |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and slab check (free)
- Masking and preparation
- Grinding if lippage or residue is present
- Diamond polishing matched to stone hardness
- Handover with gloss check and care advice
Marble Floor Polishing rates in Kolkata
| Work | Guide band | Notes |
|---|---|---|
| Buff and polish | Rs 5-15 per sq ft | Light dullness |
| Diamond polishing | Rs 15-25 per sq ft | Scratches, dull lanes |
| Grinding plus deep polish | Rs 25-35 per sq ft | Lippage, heavy wear |
| Silicate or coating | Quoted after inspection | Longer gloss life |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving Liluah
Marble Floor Polishing in Liluah is handled on scheduled routes by our Kolkata team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for Liluah addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own Liluah job handed over for your records
Keeping the finish after the job is done
| Habit | Why it matters |
|---|---|
| Dry dust mopping | Removes grit before it scratches the surface |
| pH-neutral cleaner only | Acid etches marble and bleach dulls the finish |
| Damp mop, never flooding | Standing water leaves marks and weakens joints |
| Mats at entries | Captures grit where it enters |
| Felt pads under furniture | Stops drag marks on polished surfaces |
- A light maintenance polish every 12-18 months keeps gloss without a full job
- Commercial floors are usually re-polished annually, homes every two years
- Sealer or nano coating, where applied, is refreshed on the schedule we hand over
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Machines are matched to the job. A 400 mm single-disc machine for open floors, edge machines for skirtings and staircases, and hand blocks for corners and thresholds where a machine cannot safely reach.
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
Why clients book us
- Correct grit sequence per stone hardness
- One team for grinding, polishing and sealing
- 12 years of Indian marble and stone work
- Slab thickness and hollowness checked before any grinding
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
Does Indian marble need the same treatment as Italian marble?
No. Indian marbles such as Makrana, Katni and Rajnagar are generally harder and less acid-sensitive. They take a different grit sequence and more grinding pressure, but the same acid-free cleaning discipline still applies.
Can old polish and wax be removed?
Yes. Grinding strips the residue layer completely. That is the only way a new polish bonds to the stone instead of sitting on top of old compound.
Will grinding change the colour of my floor?
It restores the original colour by removing the worn and stained top layer. Floors that have faded unevenly across rooms come back to one uniform shade.
How long does it take?
Most apartments are ground and polished in one to two days, and the floor is walkable the same evening as the final pass.
Do you polish Makrana that has gone grey?
Yes. Greyness is normally surface dirt, mop haze and worn polish. It lifts with grinding and polishing, and we show you a test patch on a hidden corner first.
Do you cover Liluah?
Yes. Liluah is on our regular route with the Kolkata team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in Liluah?
Inspection first, then scheduling. Most Liluah jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
How often does the floor need a maintenance polish?
Every 12-18 months for homes and every 8-12 months for commercial floors. It is a much smaller job than the original restoration.
Which cleaner should we use?
A pH-neutral stone cleaner with clean water, dried after mopping. Avoid acid, bleach and abrasive powders, which are the main causes of dull and etched floors.
Can maintenance work be done room by room?
Yes. We schedule it in sections so the house stays usable, and it takes a fraction of the time of a full polish.