Marble Floor Polishing in Chetla
Marble does not fade evenly. Doorways, kitchen entries and stair landings wear first, which is why floors start looking patchy. We polish the whole surface back to one uniform gloss so no room looks newer than the rest. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
- Coarse diamond passes for scratches and lippage
- Progressive grits to remove every previous scratch pattern
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Coarse diamond passes for scratches and lippage
- Progressive grits to remove every previous scratch pattern
- Fine polishing to bring up the working gloss
- Edge and corner work by hand machine
- Optional crystallisation or nano finish
- Floor washed and handed over with a gloss check
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
What each surface needs
| Grit | What it does | When it is needed |
|---|---|---|
| 60 and 100 | Cuts back lippage, deep scratches and rough patches | Uneven joints, heavy damage |
| 200 and 400 | Removes grinding marks, levels the surface | After any coarse stage |
| 800 | Closes the pores and prepares the stone | Almost every job |
| 1500 and 3000 | Working gloss and final mirror pass | Homes, lobbies, showrooms |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free, 20 minutes)
- Masking of all surfaces that should not get slurry
- Sequential diamond passes, 30-45 minutes per 100 sq ft
- Finishing pass at 1500 or 3000 grit, coating if you approve
- Handover with before and after gloss comparison
Marble Floor Polishing rates in Kolkata
| Work | Guide band | Where it applies |
|---|---|---|
| Light diamond pass | Rs 5-15 per sq ft | Sound floors, mild dulling |
| Standard diamond polishing | Rs 15-25 per sq ft | Scratch lanes, worn gloss |
| Deep diamond plus crystallisation | Rs 25-35 per sq ft | Lippage, stains, heavy wear |
| Coating after polishing | Quoted after inspection | Silicate, epoxy or nano |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving Chetla
Marble Floor Polishing in Chetla is handled on scheduled routes by our Kolkata team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for Chetla addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own Chetla job handed over for your records
Booking a crew near you
- Crews operate from two bases, so most addresses in the service cities are reached the same day for inspection
- Inspections are booked within 24-48 hours, and one-day jobs are often scheduled within the same week
- Society gate, lift and parking permissions are arranged before the crew arrives
- Machines, water supply and power needs are confirmed at booking, so nothing delays the start
- Local route days keep travel short, which keeps the per sq ft rate down
If your address is outside the listed service cities, ask before booking. We tell you honestly whether we can cover it, instead of sending a crew that bills travel into the job.
Payment terms are stated upfront: advances apply only where material has to be bought for a large job, and the balance is settled after the walkthrough so you are never paying for work you have not seen.
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Weight and load matter on upper floors and terraces. Where a slab has been laid over a void or a lightweight screed, we reduce machine weight and speed rather than risk cracking the base.
Why clients book us
- One contractor for grinding, polishing and coatings
- Gloss checked with you before the crew leaves
- 12 years, 600+ floor projects a year
- Fresh diamond segments, because worn pads leave swirl marks
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
How is diamond polishing different from the polish my housekeeping does?
Housekeeping applies cream or wax that sits on the surface and wears off in walking lanes within weeks. Diamond polishing refines the stone itself, so the finish is part of the floor.
How much marble does it remove?
Microns, not visible layers. Even a full sequence on a damaged floor only corrects the worn top surface; coarse grinding is the stage that removes more and we only use it when needed.
How glossy will the floor look?
Most marble reaches a near-mirror gloss. Statuario and Makrana take a very high gloss, while honed travertine and some Kota floors look better satin. We agree the target before starting.
How long does the finish last?
Two to three years in homes before a light maintenance pass; eight to twelve months in offices and hotels, longer with a silicate or nano coating.
Can it be done in an occupied home?
Yes. The process is wet, so dust stays low. We work room by room and leave dry paths so you can stay in the house.
Do you cover Chetla?
Yes. Chetla is on our regular route with the Kolkata team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in Chetla?
Inspection first, then scheduling. Most Chetla jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
How soon can someone come for an inspection?
Usually within 24-48 hours in our service cities. If you are on a route day, it can be the same day.
Do you cover my area?
Send the locality or PIN code and we will confirm. We would rather decline a job than travel from far and load that cost onto your rate.
Can the work be done on a weekend?
Yes. Weekend and after-hours slots are normal for occupied homes and commercial premises.