Marble Floor Polishing in Bidhan Sarani
Marble does not fade evenly. Doorways, kitchen entries and stair landings wear first, which is why floors start looking patchy. We polish the whole surface back to one uniform gloss so no room looks newer than the rest. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Polish condition check before coating
- Diamond polishing first, because coating cannot hide scratches
- Surface cleaned of residue and moisture
- Nano coating applied evenly in sections
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Diamond polishing first, because coating cannot hide scratches
- Surface cleaned of residue and moisture
- Nano coating applied evenly in sections
- Curing time allowed before use
- Edge and joint treatment by hand
- Care instructions for cleaning without stripping the coat
- Re-application schedule explained
- Polish condition check before coating
What each surface needs
| Area | Why coat it | Expected life |
|---|---|---|
| Kitchens and dining | Oil, turmeric, tea and wine spills | 12-24 months |
| Washbasins and wet areas | Hard water film and watermark rings | 12-18 months |
| Entry and lobby | Dust, grit and shoe marks | 12-24 months |
| Office and retail floors | Cleaning chemicals and trolley traffic | 12-18 months |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection to confirm the floor is polish-ready (free)
- Diamond polishing to remove scratches and dullness
- Surface cleaned and dried completely
- Nano coating applied and buffed evenly
- Curing and handover with cleaning guidance
Marble Floor Polishing rates in Kolkata
| Work | Guide band | Notes |
|---|---|---|
| Polish plus nano coating | Rs 15-25 per sq ft | Standard homes |
| Polish plus coating on heavy wear | Rs 25-35 per sq ft | Lippage, stains, patchiness |
| Nano coating only | Quoted after inspection | Floor must already be polished and sound |
| Re-application | Quoted after inspection | Every 12-24 months |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving Bidhan Sarani
Marble Floor Polishing in Bidhan Sarani is handled on scheduled routes by our Kolkata team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for Bidhan Sarani addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own Bidhan Sarani job handed over for your records
What a proper job must include
| Stage | Non-negotiable |
|---|---|
| Before starting | Gloss reading, damage map, hidden test patch, written rate |
| Preparation | Skirting, fittings and furniture edges masked |
| During | Correct pad sequence for the stone, no skipped grits |
| Finishing | Edges and corners hand-done, not left dull |
| Handover | Walkthrough with you, after-care note, waste removed |
Use this list to compare any quote you receive, ours included. If a contractor skips the test patch or the handover walkthrough, the finish will show it within weeks.
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Machines are matched to the job. A 400 mm single-disc machine for open floors, edge machines for skirtings and staircases, and hand blocks for corners and thresholds where a machine cannot safely reach.
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
Why clients book us
- 12 years of stone finishing with Akemi nano products
- Coating applied only after polishing, never as a shortcut
- pH-neutral cleaning advice so the coat is not stripped
- Visible result checked with you before handover
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
Will nano coating make my marble stain-proof?
No, and nobody should promise that. It slows absorption so you have time to wipe a spill. Leaving lemon juice or oil on the surface for hours can still mark the stone.
Does it change the appearance?
No. It is transparent and leaves the original colour and veining untouched, unlike a lacquer or film coating.
Can it be applied without polishing first?
It can, but it is a waste of money. Coating over scratches and dull patches locks them in, so we polish first or decline the job.
How long does it last?
Typically 12-24 months depending on traffic and cleaning products. Two applications a year in commercial spaces is normal.
Does it stop the floor from being slippery?
It does not increase slip resistance. For bathrooms and staircases we recommend an anti-skid treatment alongside or instead.
Do you cover Bidhan Sarani?
Yes. Bidhan Sarani is on our regular route with the Kolkata team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in Bidhan Sarani?
Inspection first, then scheduling. Most Bidhan Sarani jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
What should I check before paying?
That every surface you were quoted for has been finished, that edges and corners are not dull, that joints are clean and that the waste has been removed. Walk the floor with the crew still present, not after they leave.
Do you provide a written scope?
Yes. Surface by surface, with rate and scope, plus any optional items listed separately. Nothing is added after the work starts unless you approve a change.
Is a test patch really necessary?
It is the cheapest insurance on the job. One tile or a corner shows you the real result before you commit the whole floor.