Marble Floor Polishing in Beniatola
If your marble has lost its gloss, shows grey walking lanes or looks hazy after mopping, the finish has worn through to the stone. We restore it with a graded diamond sequence and lock the shine in, so the floor holds its look instead of going flat again in a few weeks. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Free inspection measuring lippage and slab thickness
- Tapping test for hollow slabs
- Wet grinding to keep dust down indoors
- Coarse to fine grit sequence with no skipped stages
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Wet grinding to keep dust down indoors
- Coarse to fine grit sequence with no skipped stages
- Slurry contained and vacuumed as we work
- Refining passes to remove grind marks
- Polishing to follow on the same job
- Wash-down and walkthrough
- Free inspection measuring lippage and slab thickness
- Tapping test for hollow slabs
What each surface needs
| Problem | What grinding does | Outcome |
|---|---|---|
| Lippage between slabs | Cuts the high slab to floor level | Flat floor, no trip lines |
| Dark traffic lanes | Removes the compacted worn layer | Uniform colour across the room |
| Deep scratches and gouges | Cuts back below the scratch depth | Gone, or faint on very deep damage |
| Cement, POP and paint splatter | Removes it without acid | Clean stone, no chemical risk |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection, lippage measurement and hollow test (free)
- Masking of walls, skirting, doors and furniture
- Coarse grinding, 40-60 minutes per 100 sq ft
- Refining at 200 and 400 grit, 30-45 minutes per 100 sq ft
- Polishing, wash-down and handover
Marble Floor Polishing rates in Kolkata
| Work | Guide band | Typical case |
|---|---|---|
| Light grinding with polish | Rs 15-25 per sq ft | Surface damage, patchy gloss |
| Full grinding, levelling and polish | Rs 25-35 per sq ft | Lippage, deep damage, dark lanes |
| Crystallisation after grinding | Quoted after inspection | Adds hardness and gloss |
| Grinding plus slab re-laying | Quoted per slab | Hollow or lifted slabs |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving Beniatola
Marble Floor Polishing in Beniatola is handled on scheduled routes by our Kolkata team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for Beniatola addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own Beniatola job handed over for your records
The process, step by step
- Site inspection, gloss reading and hidden test patch
- Masking of skirting, fittings, doors and furniture edges
- Residue and old polish stripping where present
- Grinding if lippage or deep damage is found
- Progressive polishing through the grit sequence
- Optional silicate, crystallisation, epoxy or nano finish
- Edge and corner hand work
- Wash-down, walkthrough and care guidance
Each stage is completed on the whole area before the next one starts, so the floor never ends up with a bright patch next to an unfinished section.
The written rate is the final amount for the agreed scope. If we open the floor and find something the inspection could not show, we stop and re-quote with you before continuing, not after.
Timing is agreed before the crew arrives: arrival window, the room sequence and the handover time are confirmed in writing, so nobody is waiting around or guessing when the floor will be free.
Waste is removed the same day. Slurry, stripped residue, used pads and packaging leave with the crew instead of going into society bins or being left for you to dispose of.
Why clients book us
- 12 years of stone grinding
- Slab thickness checked before we agree to grind
- Wet grinding with slurry contained and the site washed down
- Same team polishes after grinding, so nothing is blamed on another contractor
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
Does grinding create dust all over the house?
We grind wet, so dust becomes slurry rather than airborne powder, and we mask doors and skirting. Slurry is vacuumed and washed before we leave.
Can lippage between marble and tile be levelled?
Usually yes where the two surfaces meet at different heights. Where the step is more than a few millimetres, an exact match may not be possible and we say so before starting.
Is grinding always followed by polishing?
Yes in practice. Grinding leaves machine marks until the finer grits and polishing smooth them out, which is why the two stages are quoted together.
What if a slab is hollow?
Grinding cannot re-bond it. Loose slabs must be re-laid, and we quote that separately rather than hiding the problem under a polish.
Will grinding make my floor noticeably thinner?
It removes a fraction of a millimetre at the surface and more only where slabs are high. Average floors take several grinding cycles over their life. We measure thickness during the free inspection first.
Do you cover Beniatola?
Yes. Beniatola is on our regular route with the Kolkata team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in Beniatola?
Inspection first, then scheduling. Most Beniatola jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
How long does each step take?
As a guide, preparation is under an hour, grinding runs 25-40 minutes per 100 sq ft, polishing 15-25 minutes, and finishing plus clean-up about an hour. Bigger areas are scheduled over more days.
Can steps be skipped to save money?
Not safely. Skipping grit stages is the most common shortcut and shows up as scratch haze within weeks. If you want to reduce cost, reduce the area covered this cycle, not the process.
Do you work in one room or the whole floor at a time?
Room by room if you are living in, whole floor if the house is empty, which produces a more even finish because lighting and drying are consistent.