Marble Floor Polishing in Ashok Rajpath
Marble does not fade evenly. Doorways, kitchen entries and stair landings wear first, which is why floors start looking patchy. We polish the whole surface back to one uniform gloss so no room looks newer than the rest. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Free inspection of gloss, stains and joint condition
- Masking of skirting, walls and fittings
- Granite-specific pad sequence for the stone type
- Buffing to bring back depth and clarity
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Buffing to bring back depth and clarity
- Stain treatment for oil, rust and hard water
- Joint cleaning between slabs
- Sealing or nano coating on request
- Wash-down and gloss check with you
- Free inspection of gloss, stains and joint condition
- Masking of skirting, walls and fittings
- Granite-specific pad sequence for the stone type
What each surface needs
| Surface | Process | Result |
|---|---|---|
| Dark granite (black, brown) | Fine buff with matched pads | Deep reflective lustre |
| Light granite (grey, speckled) | Polish, then seal | Even satin to gloss |
| Granite kitchen platform | Clean, buff, seal | Stain-resistant working surface |
| Granite staircase and threshold | Edge buff and hand polish | Uniform gloss across edges |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and gloss reading (free)
- Masking and surface preparation
- Granite pad sequence and buffing
- Stain treatment where required
- Sealing, wash-down and handover
Marble Floor Polishing rates in Kolkata
| Work | Guide band | Typical case |
|---|---|---|
| Granite buffing | Rs 5-15 per sq ft | Sound floor, mild dulling |
| Diamond polishing of granite | Rs 15-25 per sq ft | Scratch lanes, worn gloss |
| Deep restoration | Rs 25-35 per sq ft | Heavy wear, stains |
| Granite sealing or nano coating | Quoted after inspection | Kitchen platforms, staircases |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving Ashok Rajpath
Marble Floor Polishing in Ashok Rajpath is handled on scheduled routes by our Kolkata team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for Ashok Rajpath addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own Ashok Rajpath job handed over for your records
The process, step by step
- Site inspection, gloss reading and hidden test patch
- Masking of skirting, fittings, doors and furniture edges
- Residue and old polish stripping where present
- Grinding if lippage or deep damage is found
- Progressive polishing through the grit sequence
- Optional silicate, crystallisation, epoxy or nano finish
- Edge and corner hand work
- Wash-down, walkthrough and care guidance
Each stage is completed on the whole area before the next one starts, so the floor never ends up with a bright patch next to an unfinished section.
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
Dust and water control is planned before we start: masking on skirting and fittings, wet working instead of dry, and slurry vacuumed as the machine moves rather than left to dry in corners.
Timing is agreed before the crew arrives: arrival window, the room sequence and the handover time are confirmed in writing, so nobody is waiting around or guessing when the floor will be free.
Why clients book us
- Sealing recommended where spills are frequent
- Samples tested on a hidden corner first
- One team for granite, marble, tile and wood
- 12 years of granite and marble work
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
Does granite need sealing?
Granite is less porous than marble but still benefits from sealing in kitchens and on staircases where water and oil sit. Sealed surfaces hold their look noticeably longer.
Can acid cleaners be used on granite?
No. Acid dulls the polished surface and can bleach the colour. Use pH-neutral cleaner and dry promptly.
How often should granite be polished?
Homes at 18-24 months, commercial floors at 8-12 months depending on traffic and cleaning method.
Can dull granite really be brought back?
Yes if the dullness is surface wear. Buffing with the correct pads restores depth and reflectivity. Stone that has been damaged by acid or heavy abrasion may need grinding first, and we will tell you after seeing it.
Do you cover Ashok Rajpath?
Yes. Ashok Rajpath is on our regular route with the Kolkata team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in Ashok Rajpath?
Inspection first, then scheduling. Most Ashok Rajpath jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
How long does each step take?
As a guide, preparation is under an hour, grinding runs 25-40 minutes per 100 sq ft, polishing 15-25 minutes, and finishing plus clean-up about an hour. Bigger areas are scheduled over more days.
Can steps be skipped to save money?
Not safely. Skipping grit stages is the most common shortcut and shows up as scratch haze within weeks. If you want to reduce cost, reduce the area covered this cycle, not the process.
Do you work in one room or the whole floor at a time?
Room by room if you are living in, whole floor if the house is empty, which produces a more even finish because lighting and drying are consistent.