Marble Fitting in Nagaland
New marble looks only as good as the fitting under it. Uneven bedding, hollow corners and wide joints cannot be polished away later, so the laying stage decides the final result. Work in Nagaland is planned as a scheduled visit: the crew and machines travel together on a fixed date, and the rate is written down after the floor is seen in person or from clear photos.
- Damage mapping and crack depth check
- Joints cleaned so epoxy bonds properly
- Pigment matched against the stone shade
- Thin epoxy for hairline joints, gel for deep cracks
At a glance
- 12 years experience
- 600+ projects a year
- Written rates
A real before and after photo is added here for the strongest result.
What is included in marble fitting
- Pigment matched against the stone shade
- Thin epoxy for hairline joints, gel for deep cracks
- Full cure before shaping and polishing
- Edges and corners hand finished
- Polish matched to the surrounding floor
- Optional sealing over repaired areas
- Damage mapping and crack depth check
- Joints cleaned so epoxy bonds properly
What each surface needs
| Damage | Method | Result |
|---|---|---|
| Open slab joints | Thin epoxy run in and levelled | Closed joint, no dirt trap |
| Chipped edges and corners | Epoxy built up and shaped | Edge rebuilt to profile |
| Cracked stair nosing | Deep tinted gel fill | Safe to walk on |
| Dull patchy gloss | Epoxy polish coat after diamond polishing | Bright even finish |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection to check whether the crack is cosmetic or structural (free)
- Cleaning of joints and cracks
- Tinted epoxy applied and left to cure
- Fill shaped flush and polished
- Handover with photos and advice on furniture that caused it
Marble Fitting rates in Nagaland
| Work | Pricing | Notes |
|---|---|---|
| Joint and crack filling | Per running ft | Colour matched |
| Chip and edge rebuilding | Per repair | Shaped and polished |
| Epoxy polish over a floor | Rs 15-25 per sq ft | After diamond polishing |
| Deep epoxy sequence with crystallisation | Rs 25-35 per sq ft | Heavy patchiness |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
The process, step by step
- Site inspection, gloss reading and hidden test patch
- Masking of skirting, fittings, doors and furniture edges
- Residue and old polish stripping where present
- Grinding if lippage or deep damage is found
- Progressive polishing through the grit sequence
- Optional silicate, crystallisation, epoxy or nano finish
- Edge and corner hand work
- Wash-down, walkthrough and care guidance
Each stage is completed on the whole area before the next one starts, so the floor never ends up with a bright patch next to an unfinished section.
Weight and load matter on upper floors and terraces. Where a slab has been laid over a void or a lightweight screed, we reduce machine weight and speed rather than risk cracking the base.
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
The written rate is the final amount for the agreed scope. If we open the floor and find something the inspection could not show, we stop and re-quote with you before continuing, not after.
Why clients book us
- Full cure before polishing, because rushing is why fills sink
- Repairs photographed before and after
- 12 years of stone repair
- Epoxy 1005 and Akemi 5010 gel in stock
Serving Nagaland and nearby areas
Nagaland jobs are booked as a fixed visit batch, so travel is planned into the date instead of being added as a surprise. Work in Nagaland is planned as a scheduled visit: the crew and machines travel together on a fixed date, and the rate is written down after the floor is seen in person or from clear photos. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Fitting - common questions
Will the repaired crack show?
With a matched tint and a flush polish it blends into the veining and is hard to find from standing height. A faint line can remain under close direct light, which is normal.
How long does an epoxy repair last?
Years under normal traffic, provided the surrounding slab is sound. If a slab is hollow or still moving, the underlying problem must be fixed first and we check that during inspection.
Is epoxy polishing the same as diamond polishing?
No. Diamond polishing refines the stone with abrasives. Epoxy polishing adds a brightening and protective treatment and works best on top of a properly polished floor.
Do we have to leave the room while it cures?
Only the work area needs to stay clear. Small fills cure in a few hours; larger repairs are left overnight before shaping and polishing.
How long does each step take?
As a guide, preparation is under an hour, grinding runs 25-40 minutes per 100 sq ft, polishing 15-25 minutes, and finishing plus clean-up about an hour. Bigger areas are scheduled over more days.
Can steps be skipped to save money?
Not safely. Skipping grit stages is the most common shortcut and shows up as scratch haze within weeks. If you want to reduce cost, reduce the area covered this cycle, not the process.
Do you work in one room or the whole floor at a time?
Room by room if you are living in, whole floor if the house is empty, which produces a more even finish because lighting and drying are consistent.