Marble Fitting in Mizoram
We lay, level and finish marble so the joints are tight, the surface is flat and the polish takes evenly. Bad fitting is what forces grinding later, and that costs more than doing it right. Work in Mizoram is planned as a scheduled visit: the crew and machines travel together on a fixed date, and the rate is written down after the floor is seen in person or from clear photos.
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
- Coarse diamond passes for scratches and lippage
- Progressive grits to remove every previous scratch pattern
At a glance
- 12 years experience
- 600+ projects a year
- Written rates
A real before and after photo is added here for the strongest result.
What is included in marble fitting
- Masking of walls, skirting and furniture edges
- Coarse diamond passes for scratches and lippage
- Progressive grits to remove every previous scratch pattern
- Fine polishing to bring up the working gloss
- Edge and corner work by hand machine
- Optional crystallisation or nano finish
- Floor washed and handed over with a gloss check
- Gloss reading and damage mapping before we quote
What each surface needs
| Grit | What it does | When it is needed |
|---|---|---|
| 60 and 100 | Cuts back lippage, deep scratches and rough patches | Uneven joints, heavy damage |
| 200 and 400 | Removes grinding marks, levels the surface | After any coarse stage |
| 800 | Closes the pores and prepares the stone | Almost every job |
| 1500 and 3000 | Working gloss and final mirror pass | Homes, lobbies, showrooms |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free, 20 minutes)
- Masking of all surfaces that should not get slurry
- Sequential diamond passes, 30-45 minutes per 100 sq ft
- Finishing pass at 1500 or 3000 grit, coating if you approve
- Handover with before and after gloss comparison
Marble Fitting rates in Mizoram
| Work | Guide band | Where it applies |
|---|---|---|
| Light diamond pass | Rs 5-15 per sq ft | Sound floors, mild dulling |
| Standard diamond polishing | Rs 15-25 per sq ft | Scratch lanes, worn gloss |
| Deep diamond plus crystallisation | Rs 25-35 per sq ft | Lippage, stains, heavy wear |
| Coating after polishing | Quoted after inspection | Silicate, epoxy or nano |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
The process, step by step
- Site inspection, gloss reading and hidden test patch
- Masking of skirting, fittings, doors and furniture edges
- Residue and old polish stripping where present
- Grinding if lippage or deep damage is found
- Progressive polishing through the grit sequence
- Optional silicate, crystallisation, epoxy or nano finish
- Edge and corner hand work
- Wash-down, walkthrough and care guidance
Each stage is completed on the whole area before the next one starts, so the floor never ends up with a bright patch next to an unfinished section.
Access is confirmed before the visit: parking, lift use, gate entry, working-hour restrictions and any society paperwork. Sorting this in advance is what stops a scheduled job from becoming a wasted trip.
Old polish, wax and cleaning residue are stripped before any new finish goes on. Layering a fresh treatment over residue is what makes floors look grey again within weeks.
Water and power are the two site requirements. We need one working socket within reach of a lead and a water point; everything else, including masking material and waste bags, comes with the crew.
Why clients book us
- Fresh diamond segments, because worn pads leave swirl marks
- Correct pad set per stone: marble, granite, Kota, terrazzo
- One contractor for grinding, polishing and coatings
- Gloss checked with you before the crew leaves
Serving Mizoram and nearby areas
Mizoram jobs are booked as a fixed visit batch, so travel is planned into the date instead of being added as a surprise. Work in Mizoram is planned as a scheduled visit: the crew and machines travel together on a fixed date, and the rate is written down after the floor is seen in person or from clear photos. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Fitting - common questions
How is diamond polishing different from the polish my housekeeping does?
Housekeeping applies cream or wax that sits on the surface and wears off in walking lanes within weeks. Diamond polishing refines the stone itself, so the finish is part of the floor.
How much marble does it remove?
Microns, not visible layers. Even a full sequence on a damaged floor only corrects the worn top surface; coarse grinding is the stage that removes more and we only use it when needed.
How glossy will the floor look?
Most marble reaches a near-mirror gloss. Statuario and Makrana take a very high gloss, while honed travertine and some Kota floors look better satin. We agree the target before starting.
How long does the finish last?
Two to three years in homes before a light maintenance pass; eight to twelve months in offices and hotels, longer with a silicate or nano coating.
Can it be done in an occupied home?
Yes. The process is wet, so dust stays low. We work room by room and leave dry paths so you can stay in the house.
How long does each step take?
As a guide, preparation is under an hour, grinding runs 25-40 minutes per 100 sq ft, polishing 15-25 minutes, and finishing plus clean-up about an hour. Bigger areas are scheduled over more days.
Can steps be skipped to save money?
Not safely. Skipping grit stages is the most common shortcut and shows up as scratch haze within weeks. If you want to reduce cost, reduce the area covered this cycle, not the process.
Do you work in one room or the whole floor at a time?
Room by room if you are living in, whole floor if the house is empty, which produces a more even finish because lighting and drying are consistent.