Engineered Wood Floor Polishing Wooden Floor Polishing in Delhi NCR
If your wood floor looks pale in the middle of the room but fine at the edges, the finish has simply worn through in the traffic path. Re-coating that path alone leaves a visible patch, which is why we do the whole room. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Moisture reading and board-soundness check
- Furniture shifting and room masking
- Dust-controlled sanding through the grit sequence
- Gap filling, crack and dent repair
At a glance
- Dust-controlled
- Gap filling
- PU / melamine / oil
A real before and after photo is added here for the strongest result.
What is included in engineered wood floor polishing
- Dust-controlled sanding through the grit sequence
- Gap filling, crack and dent repair
- Stain matching on patch repairs
- Two to three finishing coats
- Skirting, staircase and corner hand finishing
- Care sheet for mopping and monsoon humidity
- Moisture reading and board-soundness check
- Furniture shifting and room masking
What each surface needs
| Wood type | What we do | Result |
|---|---|---|
| Solid teak, sheesham, oak, walnut | Full sand and refinish, gap filling | Like-new, long finish life |
| Engineered hardwood veneer | Light sand, thin-coat finishing | Even grain, gloss restored |
| Sound floor with worn finish | Buff and re-coat, no sanding | Fresh gloss, one-day job |
| Laminate, vinyl and PVC | Cleaning and surface polish only | Cannot be sanded |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and moisture check (free)
- Masking and dust barriers
- Sanding through the grit sequence
- Gap filling, then two to three coats
- Handover after cure time with a care sheet
Engineered Wood Floor Polishing rates in Delhi NCR
| Work | Pricing | Typical scope |
|---|---|---|
| Buff and re-coat | Per sq ft | Sound floor, dull surface |
| Sanding plus two coats | Per sq ft | Worn finish, scratches |
| Sanding plus three coats | Per sq ft | Deep scratches, high traffic |
| Gap filling and repairs | Per running ft | Board gaps and cracks |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Booking a crew near you
- Crews operate from two bases, so most addresses in the service cities are reached the same day for inspection
- Inspections are booked within 24-48 hours, and one-day jobs are often scheduled within the same week
- Society gate, lift and parking permissions are arranged before the crew arrives
- Machines, water supply and power needs are confirmed at booking, so nothing delays the start
- Local route days keep travel short, which keeps the per sq ft rate down
If your address is outside the listed service cities, ask before booking. We tell you honestly whether we can cover it, instead of sending a crew that bills travel into the job.
The written rate is the final amount for the agreed scope. If we open the floor and find something the inspection could not show, we stop and re-quote with you before continuing, not after.
Where a floor has mixed surfaces, each one gets its own pad sequence and compound. Treating Kota stone and imported marble with the same approach is how floors get patchy.
Why clients book us
- Honest limits: laminate and vinyl cannot be sanded
- Same crew handles mixed marble-and-wood flats
- Low-odour water-based finishes used where possible
- 12 years of wood and stone floor work in Delhi NCR
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Engineered Wood Floor Polishing - common questions
How long before we can use the floor?
PU and lacquer floors are walkable after 24 hours and ready for furniture after 48. Melamine dries in 12-24 hours. Oil finishes can be walked on almost immediately but need re-oiling twice a year.
How often does a wooden floor need refinishing?
Homes every 6-10 years; offices and cafes every 3-5 years, or sooner if the walking lanes turn pale while the edges still look fine.
Can water stains and swollen boards be fixed?
Light black water marks and grey patches sand out. Boards that have cupped or gone spongy usually need replacing, and we identify those during the free inspection.
Will sanding fill the house with dust?
We sand with dust control and mask doorways, skirting and furniture. A fine settling of dust nearby is normal in any sanding job, and we wipe the work area before handover.
How soon can someone come for an inspection?
Usually within 24-48 hours in our service cities. If you are on a route day, it can be the same day.
Do you cover my area?
Send the locality or PIN code and we will confirm. We would rather decline a job than travel from far and load that cost onto your rate.
Can the work be done on a weekend?
Yes. Weekend and after-hours slots are normal for occupied homes and commercial premises.