Engineered Hardwood Floor Wooden Floor Polishing in Delhi NCR
A wooden floor does not fade from use alone; it dries out in summer and swells in the monsoon, and the finish wears in the walking lanes first. Sanding back to bare wood, filling the gaps and rebuilding the surface is what brings it back. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Moisture reading and board-soundness check
- Furniture shifting and room masking
- Dust-controlled sanding through the grit sequence
- Gap filling, crack and dent repair
At a glance
- Dust-controlled
- Gap filling
- PU / melamine / oil
A real before and after photo is added here for the strongest result.
What is included in engineered hardwood floor polishing
- Furniture shifting and room masking
- Dust-controlled sanding through the grit sequence
- Gap filling, crack and dent repair
- Stain matching on patch repairs
- Two to three finishing coats
- Skirting, staircase and corner hand finishing
- Care sheet for mopping and monsoon humidity
- Moisture reading and board-soundness check
What each surface needs
| Wood type | What we do | Result |
|---|---|---|
| Solid teak, sheesham, oak, walnut | Full sand and refinish, gap filling | Like-new, long finish life |
| Engineered hardwood veneer | Light sand, thin-coat finishing | Even grain, gloss restored |
| Sound floor with worn finish | Buff and re-coat, no sanding | Fresh gloss, one-day job |
| Laminate, vinyl and PVC | Cleaning and surface polish only | Cannot be sanded |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and moisture check (free)
- Masking and dust barriers
- Sanding through the grit sequence
- Gap filling, then two to three coats
- Handover after cure time with a care sheet
Engineered Hardwood Floor Polishing rates in Delhi NCR
| Work | Pricing | Typical scope |
|---|---|---|
| Buff and re-coat | Per sq ft | Sound floor, dull surface |
| Sanding plus two coats | Per sq ft | Worn finish, scratches |
| Sanding plus three coats | Per sq ft | Deep scratches, high traffic |
| Gap filling and repairs | Per running ft | Board gaps and cracks |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
How to get a quote that does not change
- WhatsApp photos of the dullest area and the worst stain speed up the first estimate
- A free on-site inspection gives the final figure, because gloss readings and damage depth cannot be judged from a photo
- The written quote lists surface by surface: area, rate, scope and exclusions
- Coatings, crack repairs and slab replacement appear as separate optional lines
- The figure is valid for thirty days unless you ask us to hold it longer
If a contractor quotes a single number for a whole house without inspecting it, that number will change once work starts. We would rather quote after looking.
Where a floor has mixed surfaces, each one gets its own pad sequence and compound. Treating Kota stone and imported marble with the same approach is how floors get patchy.
The written rate is the final amount for the agreed scope. If we open the floor and find something the inspection could not show, we stop and re-quote with you before continuing, not after.
Why clients book us
- Honest limits: laminate and vinyl cannot be sanded
- Same crew handles mixed marble-and-wood flats
- Low-odour water-based finishes used where possible
- 12 years of wood and stone floor work in Delhi NCR
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Engineered Hardwood Floor Polishing - common questions
How long before we can use the floor?
PU and lacquer floors are walkable after 24 hours and ready for furniture after 48. Melamine dries in 12-24 hours. Oil finishes can be walked on almost immediately but need re-oiling twice a year.
How often does a wooden floor need refinishing?
Homes every 6-10 years; offices and cafes every 3-5 years, or sooner if the walking lanes turn pale while the edges still look fine.
Can water stains and swollen boards be fixed?
Light black water marks and grey patches sand out. Boards that have cupped or gone spongy usually need replacing, and we identify those during the free inspection.
Will sanding fill the house with dust?
We sand with dust control and mask doorways, skirting and furniture. A fine settling of dust nearby is normal in any sanding job, and we wipe the work area before handover.
Can I get a quote on WhatsApp?
Yes as an indicative band. Send photos in daylight of the dullest area, any stains and one close-up of the surface. The final figure is confirmed after the free on-site inspection.
How long is the quote valid?
Thirty days from the inspection date. Material and product rates move, so we do not hold figures indefinitely, but we will tell you if anything changes.
Is the inspection really free?
Yes. There is no charge for the site visit or the measurement, and no obligation to proceed afterwards.