Wooden Tile Polishing in Delhi NCR
A wooden floor does not fade from use alone; it dries out in summer and swells in the monsoon, and the finish wears in the walking lanes first. Sanding back to bare wood, filling the gaps and rebuilding the surface is what brings it back. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Moisture reading and board-soundness check
- Furniture shifting and room masking
- Dust-controlled sanding through the grit sequence
- Gap filling, crack and dent repair
At a glance
- Dust-controlled
- Gap filling
- PU / melamine / oil
A real before and after photo is added here for the strongest result.
What is included in wooden tile polishing
- Dust-controlled sanding through the grit sequence
- Gap filling, crack and dent repair
- Stain matching on patch repairs
- Two to three finishing coats
- Skirting, staircase and corner hand finishing
- Care sheet for mopping and monsoon humidity
- Moisture reading and board-soundness check
- Furniture shifting and room masking
What each surface needs
| Wood type | What we do | Result |
|---|---|---|
| Solid teak, sheesham, oak, walnut | Full sand and refinish, gap filling | Like-new, long finish life |
| Engineered hardwood veneer | Light sand, thin-coat finishing | Even grain, gloss restored |
| Sound floor with worn finish | Buff and re-coat, no sanding | Fresh gloss, one-day job |
| Laminate, vinyl and PVC | Cleaning and surface polish only | Cannot be sanded |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and moisture check (free)
- Masking and dust barriers
- Sanding through the grit sequence
- Gap filling, then two to three coats
- Handover after cure time with a care sheet
Wooden Tile Polishing rates in Delhi NCR
| Work | Pricing | Typical scope |
|---|---|---|
| Buff and re-coat | Per sq ft | Sound floor, dull surface |
| Sanding plus two coats | Per sq ft | Worn finish, scratches |
| Sanding plus three coats | Per sq ft | Deep scratches, high traffic |
| Gap filling and repairs | Per running ft | Board gaps and cracks |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Keeping the finish after the job is done
| Habit | Why it matters |
|---|---|
| Dry dust mopping | Removes grit before it scratches the surface |
| pH-neutral cleaner only | Acid etches marble and bleach dulls the finish |
| Damp mop, never flooding | Standing water leaves marks and weakens joints |
| Mats at entries | Captures grit where it enters |
| Felt pads under furniture | Stops drag marks on polished surfaces |
- A light maintenance polish every 12-18 months keeps gloss without a full job
- Commercial floors are usually re-polished annually, homes every two years
- Sealer or nano coating, where applied, is refreshed on the schedule we hand over
The written rate is the final amount for the agreed scope. If we open the floor and find something the inspection could not show, we stop and re-quote with you before continuing, not after.
Timing is agreed before the crew arrives: arrival window, the room sequence and the handover time are confirmed in writing, so nobody is waiting around or guessing when the floor will be free.
Waste is removed the same day. Slurry, stripped residue, used pads and packaging leave with the crew instead of going into society bins or being left for you to dispose of.
Why clients book us
- Same crew handles mixed marble-and-wood flats
- Low-odour water-based finishes used where possible
- 12 years of wood and stone floor work in Delhi NCR
- Dust control as standard so wardrobes and curtains stay clean
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Wooden Tile Polishing - common questions
How long before we can use the floor?
PU and lacquer floors are walkable after 24 hours and ready for furniture after 48. Melamine dries in 12-24 hours. Oil finishes can be walked on almost immediately but need re-oiling twice a year.
How often does a wooden floor need refinishing?
Homes every 6-10 years; offices and cafes every 3-5 years, or sooner if the walking lanes turn pale while the edges still look fine.
Can water stains and swollen boards be fixed?
Light black water marks and grey patches sand out. Boards that have cupped or gone spongy usually need replacing, and we identify those during the free inspection.
Will sanding fill the house with dust?
We sand with dust control and mask doorways, skirting and furniture. A fine settling of dust nearby is normal in any sanding job, and we wipe the work area before handover.
How often does the floor need a maintenance polish?
Every 12-18 months for homes and every 8-12 months for commercial floors. It is a much smaller job than the original restoration.
Which cleaner should we use?
A pH-neutral stone cleaner with clean water, dried after mopping. Avoid acid, bleach and abrasive powders, which are the main causes of dull and etched floors.
Can maintenance work be done room by room?
Yes. We schedule it in sections so the house stays usable, and it takes a fraction of the time of a full polish.