White Marble Floor Polishing in Kolkata
The job on white stone is patience: gradual grits, controlled heat and no acid anywhere near it. Done properly, a white marble floor comes back to a clean, deep white rather than a grey-ish shine. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
- Coarse diamond passes for scratches and lippage
- Progressive grits to remove every previous scratch pattern
At a glance
- 12 years experience
- 600+ projects a year
- Written rates
A real before and after photo is added here for the strongest result.
What is included in white marble floor polishing
- Progressive grits to remove every previous scratch pattern
- Fine polishing to bring up the working gloss
- Edge and corner work by hand machine
- Optional crystallisation or nano finish
- Floor washed and handed over with a gloss check
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
- Coarse diamond passes for scratches and lippage
What each surface needs
| Grit | What it does | When it is needed |
|---|---|---|
| 60 and 100 | Cuts back lippage, deep scratches and rough patches | Uneven joints, heavy damage |
| 200 and 400 | Removes grinding marks, levels the surface | After any coarse stage |
| 800 | Closes the pores and prepares the stone | Almost every job |
| 1500 and 3000 | Working gloss and final mirror pass | Homes, lobbies, showrooms |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free, 20 minutes)
- Masking of all surfaces that should not get slurry
- Sequential diamond passes, 30-45 minutes per 100 sq ft
- Finishing pass at 1500 or 3000 grit, coating if you approve
- Handover with before and after gloss comparison
White Marble Floor Polishing rates in Kolkata
| Work | Guide band | Where it applies |
|---|---|---|
| Light diamond pass | Rs 5-15 per sq ft | Sound floors, mild dulling |
| Standard diamond polishing | Rs 15-25 per sq ft | Scratch lanes, worn gloss |
| Deep diamond plus crystallisation | Rs 25-35 per sq ft | Lippage, stains, heavy wear |
| Coating after polishing | Quoted after inspection | Silicate, epoxy or nano |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
What changes the price for white marble floor polishing in Kolkata
| Factor | Effect on rate | What to expect |
|---|---|---|
| Total area | Bigger areas cost less per sq ft | Slab rates above 1,000 sq ft |
| Damage depth | Grinding raises the rate | Decided by the test patch |
| Stone type | Imported and filled slabs take longer | See the surface table |
| Access | Upper floors and corners take longer | Confirmed before booking |
Ask for one written rate per surface. A single number for the whole house without an inspection always changes later.
Booking, access and scheduling
- Inspection booked within 24-48 hours; the written quote follows the same visit
- Work usually starts within a week of approval, sooner if you are flexible on dates
- Society gate, lift, parking and working-hour rules arranged before the crew arrives
- Water point, power and work area confirmed at booking so setup takes minutes
- Occupied premises are done room by room or after hours, at no surprise premium
| Job size | Typical duration |
|---|---|
| Bathroom or kitchen | Same day |
| Single room | One working day |
| Full 2-3 BHK | One to two days |
| Lobby or commercial floor | Phased, often overnight |
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
Dust and water control is planned before we start: masking on skirting and fittings, wet working instead of dry, and slurry vacuumed as the machine moves rather than left to dry in corners.
Timing is agreed before the crew arrives: arrival window, the room sequence and the handover time are confirmed in writing, so nobody is waiting around or guessing when the floor will be free.
Why clients book us
- Correct pad set per stone: marble, granite, Kota, terrazzo
- One contractor for grinding, polishing and coatings
- Gloss checked with you before the crew leaves
- 12 years, 600+ floor projects a year
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
White Marble Floor Polishing - common questions
How is diamond polishing different from the polish my housekeeping does?
Housekeeping applies cream or wax that sits on the surface and wears off in walking lanes within weeks. Diamond polishing refines the stone itself, so the finish is part of the floor.
How much marble does it remove?
Microns, not visible layers. Even a full sequence on a damaged floor only corrects the worn top surface; coarse grinding is the stage that removes more and we only use it when needed.
How glossy will the floor look?
Most marble reaches a near-mirror gloss. Statuario and Makrana take a very high gloss, while honed travertine and some Kota floors look better satin. We agree the target before starting.
How long does the finish last?
Two to three years in homes before a light maintenance pass; eight to twelve months in offices and hotels, longer with a silicate or nano coating.
Can it be done in an occupied home?
Yes. The process is wet, so dust stays low. We work room by room and leave dry paths so you can stay in the house.
Is the price negotiable?
The rate per sq ft is not inflated to leave room for haggling. We scope honestly: if the floor needs only a buff, we quote a buff instead of a full diamond job, and tell you when the cheaper option will hold.
Do you take advance payment?
The package is confirmed in writing first. Advance for material is normal on large jobs; the balance is settled after the walkthrough.
How far in advance should I book?
A week is comfortable. During festival and wedding season, two weeks is safer because crews are booked out for hotel and banquet work.
What access do you need?
A water point, a working power socket, and a clear route for the machines. Society permission for lift use is helpful for upper floors.
Can the job be split across weekends?
Yes. Many clients do one or two rooms each weekend. We keep the same rate per sq ft and you are not billed twice for travel within the same batch.