Stone Surface Grinding And Marble Floor Grinding in Delhi NCR
Grinding is the heavy stage before polishing, and the only way to fix what polishing cannot touch: slabs at different heights, dark traffic lanes, deep scratches, paint and cement splatter, and years of built-up polish residue. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Free inspection measuring lippage and slab thickness
- Tapping test for hollow slabs
- Wet grinding to keep dust down indoors
- Coarse to fine grit sequence with no skipped stages
At a glance
- Lippage removal
- Wet grinding
- Thickness checked
A real before and after photo is added here for the strongest result.
What is included in stone surface grinding and polishing
- Free inspection measuring lippage and slab thickness
- Tapping test for hollow slabs
- Wet grinding to keep dust down indoors
- Coarse to fine grit sequence with no skipped stages
- Slurry contained and vacuumed as we work
- Refining passes to remove grind marks
- Polishing to follow on the same job
- Wash-down and walkthrough
What each surface needs
| Problem | What grinding does | Outcome |
|---|---|---|
| Lippage between slabs | Cuts the high slab to floor level | Flat floor, no trip lines |
| Dark traffic lanes | Removes the compacted worn layer | Uniform colour across the room |
| Deep scratches and gouges | Cuts back below the scratch depth | Gone, or faint on very deep damage |
| Cement, POP and paint splatter | Removes it without acid | Clean stone, no chemical risk |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection, lippage measurement and hollow test (free)
- Masking of walls, skirting, doors and furniture
- Coarse grinding, 40-60 minutes per 100 sq ft
- Refining at 200 and 400 grit, 30-45 minutes per 100 sq ft
- Polishing, wash-down and handover
Stone Surface Grinding And Polishing rates in Delhi NCR
| Work | Guide band | Typical case |
|---|---|---|
| Light grinding with polish | Rs 15-25 per sq ft | Surface damage, patchy gloss |
| Full grinding, levelling and polish | Rs 25-35 per sq ft | Lippage, deep damage, dark lanes |
| Crystallisation after grinding | Quoted after inspection | Adds hardness and gloss |
| Grinding plus slab re-laying | Quoted per slab | Hollow or lifted slabs |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Keeping the finish after the job is done
| Habit | Why it matters |
|---|---|
| Dry dust mopping | Removes grit before it scratches the surface |
| pH-neutral cleaner only | Acid etches marble and bleach dulls the finish |
| Damp mop, never flooding | Standing water leaves marks and weakens joints |
| Mats at entries | Captures grit where it enters |
| Felt pads under furniture | Stops drag marks on polished surfaces |
- A light maintenance polish every 12-18 months keeps gloss without a full job
- Commercial floors are usually re-polished annually, homes every two years
- Sealer or nano coating, where applied, is refreshed on the schedule we hand over
Old polish, wax and cleaning residue are stripped before any new finish goes on. Layering a fresh treatment over residue is what makes floors look grey again within weeks.
Dust and water control is planned before we start: masking on skirting and fittings, wet working instead of dry, and slurry vacuumed as the machine moves rather than left to dry in corners.
Why clients book us
- Same team polishes after grinding, so nothing is blamed on another contractor
- Hollow and thin slabs flagged honestly instead of ground
- 12 years of stone grinding in Delhi NCR
- Slab thickness checked before we agree to grind
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Stone Surface Grinding And Polishing - common questions
Will grinding make my floor noticeably thinner?
It removes a fraction of a millimetre at the surface and more only where slabs are high. Average floors take several grinding cycles over their life. We measure thickness during the free inspection first.
Does grinding create dust all over the house?
We grind wet, so dust becomes slurry rather than airborne powder, and we mask doors and skirting. Slurry is vacuumed and washed before we leave.
Can lippage between marble and tile be levelled?
Usually yes where the two surfaces meet at different heights. Where the step is more than a few millimetres, an exact match may not be possible and we say so before starting.
Is grinding always followed by polishing?
Yes in practice. Grinding leaves machine marks until the finer grits and polishing smooth them out, which is why the two stages are quoted together.
What if a slab is hollow?
Grinding cannot re-bond it. Loose slabs must be re-laid, and we quote that separately rather than hiding the problem under a polish.
How often does the floor need a maintenance polish?
Every 12-18 months for homes and every 8-12 months for commercial floors. It is a much smaller job than the original restoration.
Which cleaner should we use?
A pH-neutral stone cleaner with clean water, dried after mopping. Avoid acid, bleach and abrasive powders, which are the main causes of dull and etched floors.
Can maintenance work be done room by room?
Yes. We schedule it in sections so the house stays usable, and it takes a fraction of the time of a full polish.