Silicate Marble Polishing in Imphal
Silicate treatment is what gives marble a wet, deep gloss instead of a thin surface shine. The chemical reacts with the calcium in the stone and hardens the top layer, so the finish holds through mopping and footfall far longer than plain polishing. Work in Imphal is planned as a scheduled visit: the crew and machines travel together on a fixed date, and the rate is written down after the floor is seen in person or from clear photos.
- Gloss and polish-condition check first
- Masking of skirting, walls and fittings
- Diamond polishing to the grit the treatment needs
- Even section-by-section silicate application
At a glance
- Sil200 / Sil800
- Wet-look gloss
- Applied after polishing
A real before and after photo is added here for the strongest result.
What is included in silicate marble polishing
- Diamond polishing to the grit the treatment needs
- Even section-by-section silicate application
- Machine buffing to remove residue and streaks
- Edge and corner treatment by hand
- Walkway protection until the surface sets
- Cleaning advice so acid cleaners never touch it
- Gloss and polish-condition check first
- Masking of skirting, walls and fittings
What each surface needs
| Treatment | Character | Best for |
|---|---|---|
| Sil200 | Fast build, strong initial gloss | Homes and moderate traffic |
| Sil800 | Deeper wet look, holds gloss longer | Lobbies, showrooms, hotels |
| Over new stone | Protects an unworn surface | Recently laid or newly polished floors |
| Over worn stone | Short-lived unless polished first | Only after a full diamond sequence |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Assessment to confirm silicate suits the stone and the room
- Diamond polishing to 800-1500 grit so there is a finish worth locking in
- Silicate applied in sections and buffed while it reacts
- Second pass on heavy areas for even gloss
- Gloss check and a list of cleaners to avoid
Silicate Marble Polishing rates in Imphal
| Work | Guide band | Notes |
|---|---|---|
| Polish plus Sil200 | Rs 15-25 per sq ft | Homes, standard traffic |
| Polish plus Sil800 | Rs 25-35 per sq ft | Lobbies, hotels, heavy traffic |
| Silicate over an already polished floor | Quoted after inspection | Floor must still be sound |
| Repeat maintenance treatment | Quoted after inspection | Every 1-3 years |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Tiles or marble: what each one needs
| Tiles (vitrified, ceramic) | Marble | |
|---|---|---|
| What dulls | Surface residue and micro-scratches | Worn polished layer, etching |
| Restoring it | Deep clean, surface refine | Grinding and diamond polishing |
| Staining | Grout lines first | Stone surface and joints |
| Slip risk | High on glossy tile when wet | High on mirror-polished stone |
| Best finish for wet areas | Clean plus anti-skid | Satin plus anti-skid |
In most homes both are present in the same flat, which is why we quote surface by surface instead of giving one blended rate.
Waste is removed the same day. Slurry, stripped residue, used pads and packaging leave with the crew instead of going into society bins or being left for you to dispose of.
Nothing is hidden behind a shine. Where a surface has damage that polishing cannot correct, we mark it during inspection and put it in writing, so expectations are set before work starts rather than argued over afterwards.
After-care guidance is handed over in writing: which cleaner to use, how to mop, and what to avoid during the first week. Most repeat problems trace back to cleaning products rather than the work itself.
Why clients book us
- Product chosen for the stone, not one bottle for all
- Residue buffed off before handover
- 12 years of stone finishing
- We polish before we treat, never over a dull surface
Serving Imphal and nearby areas
Imphal jobs are booked as a fixed visit batch, so travel is planned into the date instead of being added as a surprise. Work in Imphal is planned as a scheduled visit: the crew and machines travel together on a fixed date, and the rate is written down after the floor is seen in person or from clear photos. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Silicate Marble Polishing - common questions
How long does it last?
Roughly two to three years in homes and one to two years in heavy-footfall lobbies. Using a pH-neutral cleaner instead of acid is the biggest factor.
Can it be applied to a floor that was never polished?
It can, but it is rarely worth it, because silicate amplifies whatever surface it meets and locks in scratches. We polish to 800-1500 grit first or refuse the treatment.
Will it make the floor slippery?
A high-gloss finish is smoother when wet. In bathrooms, kitchens and on staircases we recommend a satin or crystallised finish instead of mirror gloss.
How long before we can walk on it?
The floor is walkable the same evening. Only normal drying after the polishing stage is needed, with no curing days.
Is silicate the same as waxing the floor?
No. Wax sits on the surface and wipes off. Silicate reacts with the calcium in the marble and hardens the surface layer, so the gloss is part of the stone and survives mopping.
Can tiles be polished like marble?
Tiles are refined and cleaned, not ground like stone. Polishing a vitrified tile past its factory finish wears the surface, so we clean and seal instead, or polish only where the tile type allows it.
Which is better for a bathroom floor?
Neither should be mirror-glossy when wet. Tile with anti-skid treatment, or honed stone with anti-skid, is the safer and more practical choice.
Do floors with both need separate visits?
No. One crew handles tiles, grout and stone in the same visit, which also avoids the joint line between two trades becoming anyone's excuse.