Marble Restoration in Patna
Polishing brings back gloss. Restoration fixes what dulled the floor in the first place: white etch marks under the water cooler, rust rings under planters, hairline cracks at the joints, chipped stair edges and slabs sitting at different heights. Patna homes lean heavily on marble and Kota stone laid years ago, and dust plus monsoon humidity make those floors look permanently grey. Grinding is usually needed before polishing shows any real gloss.
- Free inspection measuring lippage and slab thickness
- Tapping test for hollow slabs
- Wet grinding to keep dust down indoors
- Coarse to fine grit sequence with no skipped stages
At a glance
- Etch repair
- Poultice treatment
- Colour-matched fills
A real before and after photo is added here for the strongest result.
What is included in marble restoration
- Free inspection measuring lippage and slab thickness
- Tapping test for hollow slabs
- Wet grinding to keep dust down indoors
- Coarse to fine grit sequence with no skipped stages
- Slurry contained and vacuumed as we work
- Refining passes to remove grind marks
- Polishing to follow on the same job
- Wash-down and walkthrough
What each surface needs
| Problem | What grinding does | Outcome |
|---|---|---|
| Lippage between slabs | Cuts the high slab to floor level | Flat floor, no trip lines |
| Dark traffic lanes | Removes the compacted worn layer | Uniform colour across the room |
| Deep scratches and gouges | Cuts back below the scratch depth | Gone, or faint on very deep damage |
| Cement, POP and paint splatter | Removes it without acid | Clean stone, no chemical risk |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection, lippage measurement and hollow test (free)
- Masking of walls, skirting, doors and furniture
- Coarse grinding, 40-60 minutes per 100 sq ft
- Refining at 200 and 400 grit, 30-45 minutes per 100 sq ft
- Polishing, wash-down and handover
Marble Restoration rates in Patna
| Work | Guide band | Typical case |
|---|---|---|
| Light grinding with polish | Rs 15-25 per sq ft | Surface damage, patchy gloss |
| Full grinding, levelling and polish | Rs 25-35 per sq ft | Lippage, deep damage, dark lanes |
| Crystallisation after grinding | Quoted after inspection | Adds hardness and gloss |
| Grinding plus slab re-laying | Quoted per slab | Hollow or lifted slabs |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
How to get a quote that does not change
- WhatsApp photos of the dullest area and the worst stain speed up the first estimate
- A free on-site inspection gives the final figure, because gloss readings and damage depth cannot be judged from a photo
- The written quote lists surface by surface: area, rate, scope and exclusions
- Coatings, crack repairs and slab replacement appear as separate optional lines
- The figure is valid for thirty days unless you ask us to hold it longer
If a contractor quotes a single number for a whole house without inspecting it, that number will change once work starts. We would rather quote after looking.
Dust and water control is planned before we start: masking on skirting and fittings, wet working instead of dry, and slurry vacuumed as the machine moves rather than left to dry in corners.
After-care guidance is handed over in writing: which cleaner to use, how to mop, and what to avoid during the first week. Most repeat problems trace back to cleaning products rather than the work itself.
Quality is checked twice: once mid-job, when the first section is finished and you can see the achievable gloss, and once at handover when the whole surface should read evenly under daylight and under your own lighting.
Why clients book us
- Wet grinding with slurry contained and the site washed down
- Same team polishes after grinding, so nothing is blamed on another contractor
- Hollow and thin slabs flagged honestly instead of ground
- 12 years of stone grinding
Serving Patna and nearby areas
Patna work is booked as a scheduled visit batch with the full machine set. Patna homes lean heavily on marble and Kota stone laid years ago, and dust plus monsoon humidity make those floors look permanently grey. Grinding is usually needed before polishing shows any real gloss. Inspections are booked within 24-48 hours and most jobs take 1-2 days depending on area. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Restoration - common questions
Will grinding make my floor noticeably thinner?
It removes a fraction of a millimetre at the surface and more only where slabs are high. Average floors take several grinding cycles over their life. We measure thickness during the free inspection first.
Does grinding create dust all over the house?
We grind wet, so dust becomes slurry rather than airborne powder, and we mask doors and skirting. Slurry is vacuumed and washed before we leave.
Can lippage between marble and tile be levelled?
Usually yes where the two surfaces meet at different heights. Where the step is more than a few millimetres, an exact match may not be possible and we say so before starting.
Is grinding always followed by polishing?
Yes in practice. Grinding leaves machine marks until the finer grits and polishing smooth them out, which is why the two stages are quoted together.
What if a slab is hollow?
Grinding cannot re-bond it. Loose slabs must be re-laid, and we quote that separately rather than hiding the problem under a polish.
Can I get a quote on WhatsApp?
Yes as an indicative band. Send photos in daylight of the dullest area, any stains and one close-up of the surface. The final figure is confirmed after the free on-site inspection.
How long is the quote valid?
Thirty days from the inspection date. Material and product rates move, so we do not hold figures indefinitely, but we will tell you if anything changes.
Is the inspection really free?
Yes. There is no charge for the site visit or the measurement, and no obligation to proceed afterwards.