Marble Polishing With Silicate in Delhi NCR
Silicate treatment is what gives marble a wet, deep gloss instead of a thin surface shine. The chemical reacts with the calcium in the stone and hardens the top layer, so the finish holds through mopping and footfall far longer than plain polishing. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Free inspection with a residue test
- Masking of skirting and furniture edges
- pH-neutral deep cleaning, no acid
- Residue and soap film stripping
At a glance
- Sil200 / Sil800
- Wet-look gloss
- Applied after polishing
A real before and after photo is added here for the strongest result.
What is included in marble polishing with silicate delhi ncr
- Masking of skirting and furniture edges
- pH-neutral deep cleaning, no acid
- Residue and soap film stripping
- Grout-line and edge cleaning
- Stain treatment where present
- Optional polishing if the surface needs it
- Drying and care guidance
- Free inspection with a residue test
What each surface needs
| Test | What it means | Correct job |
|---|---|---|
| Wipes clean, still grey | Surface is worn | Polishing needed |
| Feels tacky or streaky | Residue build-up | Deep cleaning only |
| Local dark patches | Stains | Stain treatment |
| White marks near taps | Hard water scale | De-scale and neutral clean |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and residue test (free)
- Masking and preparation
- pH-neutral deep clean and stripping
- Joint and edge cleaning
- Handover with a cleaning routine for daily care
Marble Polishing With Silicate Delhi Ncr rates in Delhi NCR
| Work | Guide band | Notes |
|---|---|---|
| Deep cleaning | Rs 5-15 per sq ft | Residue and soil |
| Deep clean with stain treatment | Rs 15-25 per sq ft | Oil, rust, scale |
| Cleaning plus polishing | Rs 25-35 per sq ft | Worn surface |
| Sealing after cleaning | Quoted after inspection | Optional |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
The process, step by step
- Site inspection, gloss reading and hidden test patch
- Masking of skirting, fittings, doors and furniture edges
- Residue and old polish stripping where present
- Grinding if lippage or deep damage is found
- Progressive polishing through the grit sequence
- Optional silicate, crystallisation, epoxy or nano finish
- Edge and corner hand work
- Wash-down, walkthrough and care guidance
Each stage is completed on the whole area before the next one starts, so the floor never ends up with a bright patch next to an unfinished section.
Waste is removed the same day. Slurry, stripped residue, used pads and packaging leave with the crew instead of going into society bins or being left for you to dispose of.
Nothing is hidden behind a shine. Where a surface has damage that polishing cannot correct, we mark it during inspection and put it in writing, so expectations are set before work starts rather than argued over afterwards.
After-care guidance is handed over in writing: which cleaner to use, how to mop, and what to avoid during the first week. Most repeat problems trace back to cleaning products rather than the work itself.
Why clients book us
- Residue test done first, so you pay only for the job you need
- pH-neutral products on all calcite stone
- Honest advice when cleaning alone is not enough
- Daily-care routine explained at handover
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Polishing With Silicate Delhi Ncr - common questions
Do I need cleaning or polishing?
Test one patch with a clean damp cloth. If it wipes clean but still looks grey, the surface is worn and needs polishing. If the cloth comes away dirty or the floor is streaky, it needs deep cleaning.
How often should marble be deep cleaned?
Every six to twelve months in homes, and every three to six months in commercial spaces. Daily mopping with the wrong product makes build-up worse, not better.
Which cleaner should we use daily?
A pH-neutral stone cleaner with clean water, and dry the surface afterwards. Acid and abrasive cleaners damage polished marble within a few uses.
Can cleaning remove white patches near taps?
Hard-water scale yes, with a descaling clean. Etch marks caused by acid need light grinding and polishing, which is a different job.
How long does each step take?
As a guide, preparation is under an hour, grinding runs 25-40 minutes per 100 sq ft, polishing 15-25 minutes, and finishing plus clean-up about an hour. Bigger areas are scheduled over more days.
Can steps be skipped to save money?
Not safely. Skipping grit stages is the most common shortcut and shows up as scratch haze within weeks. If you want to reduce cost, reduce the area covered this cycle, not the process.
Do you work in one room or the whole floor at a time?
Room by room if you are living in, whole floor if the house is empty, which produces a more even finish because lighting and drying are consistent.