Marble Polishing With Nano Marble Polishing with Nano Coating in Delhi NCR
A nano coating is an invisible protective layer applied after polishing. It does not change the look of the stone, but it slows down how quickly tea, oil, hard water and coloured liquids soak in, which is what normally ruins a polished floor. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Polish condition check before coating
- Diamond polishing first, because coating cannot hide scratches
- Surface cleaned of residue and moisture
- Nano coating applied evenly in sections
At a glance
- Akemi nano
- Invisible protection
- 12-24 months
A real before and after photo is added here for the strongest result.
What is included in marble polishing with nano and epoxy delhi ncr
- Surface cleaned of residue and moisture
- Nano coating applied evenly in sections
- Curing time allowed before use
- Edge and joint treatment by hand
- Care instructions for cleaning without stripping the coat
- Re-application schedule explained
- Polish condition check before coating
- Diamond polishing first, because coating cannot hide scratches
What each surface needs
| Area | Why coat it | Expected life |
|---|---|---|
| Kitchens and dining | Oil, turmeric, tea and wine spills | 12-24 months |
| Washbasins and wet areas | Hard water film and watermark rings | 12-18 months |
| Entry and lobby | Dust, grit and shoe marks | 12-24 months |
| Office and retail floors | Cleaning chemicals and trolley traffic | 12-18 months |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection to confirm the floor is polish-ready (free)
- Diamond polishing to remove scratches and dullness
- Surface cleaned and dried completely
- Nano coating applied and buffed evenly
- Curing and handover with cleaning guidance
Marble Polishing With Nano and Epoxy Delhi Ncr rates in Delhi NCR
| Work | Guide band | Notes |
|---|---|---|
| Polish plus nano coating | Rs 15-25 per sq ft | Standard homes |
| Polish plus coating on heavy wear | Rs 25-35 per sq ft | Lippage, stains, patchiness |
| Nano coating only | Quoted after inspection | Floor must already be polished and sound |
| Re-application | Quoted after inspection | Every 12-24 months |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Keeping the finish after the job is done
| Habit | Why it matters |
|---|---|
| Dry dust mopping | Removes grit before it scratches the surface |
| pH-neutral cleaner only | Acid etches marble and bleach dulls the finish |
| Damp mop, never flooding | Standing water leaves marks and weakens joints |
| Mats at entries | Captures grit where it enters |
| Felt pads under furniture | Stops drag marks on polished surfaces |
- A light maintenance polish every 12-18 months keeps gloss without a full job
- Commercial floors are usually re-polished annually, homes every two years
- Sealer or nano coating, where applied, is refreshed on the schedule we hand over
Nothing is hidden behind a shine. Where a surface has damage that polishing cannot correct, we mark it during inspection and put it in writing, so expectations are set before work starts rather than argued over afterwards.
Where a floor has mixed surfaces, each one gets its own pad sequence and compound. Treating Kota stone and imported marble with the same approach is how floors get patchy.
Protection is planned, not improvised. Furniture is moved to one side and covered, curtain hems are lifted, and a walking route is kept clear throughout so the household can still move around.
Why clients book us
- Coating applied only after polishing, never as a shortcut
- pH-neutral cleaning advice so the coat is not stripped
- Visible result checked with you before handover
- Clear re-application schedule instead of vague promises
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Polishing With Nano and Epoxy Delhi Ncr - common questions
Will nano coating make my marble stain-proof?
No, and nobody should promise that. It slows absorption so you have time to wipe a spill. Leaving lemon juice or oil on the surface for hours can still mark the stone.
Does it change the appearance?
No. It is transparent and leaves the original colour and veining untouched, unlike a lacquer or film coating.
Can it be applied without polishing first?
It can, but it is a waste of money. Coating over scratches and dull patches locks them in, so we polish first or decline the job.
How long does it last?
Typically 12-24 months depending on traffic and cleaning products. Two applications a year in commercial spaces is normal.
Does it stop the floor from being slippery?
It does not increase slip resistance. For bathrooms and staircases we recommend an anti-skid treatment alongside or instead.
How often does the floor need a maintenance polish?
Every 12-18 months for homes and every 8-12 months for commercial floors. It is a much smaller job than the original restoration.
Which cleaner should we use?
A pH-neutral stone cleaner with clean water, dried after mopping. Avoid acid, bleach and abrasive powders, which are the main causes of dull and etched floors.
Can maintenance work be done room by room?
Yes. We schedule it in sections so the house stays usable, and it takes a fraction of the time of a full polish.