Marble Floor Polishing in Siri Fort Delhi
Marble does not fade evenly. Doorways, kitchen entries and stair landings wear first, which is why floors start looking patchy. We polish the whole surface back to one uniform gloss so no room looks newer than the rest. Delhi floors take a beating from dust, metro-era construction grit and hard water. Makrana, Katni and Kota dominate older colonies, while newer builder floors use imported marble.
- Free inspection and test patch
- Masking of walls, skirting and furniture edges
- Wet sanding through the grit sequence
- Slurry vacuumed as work proceeds
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Slurry vacuumed as work proceeds
- Damage and joint treatment where found
- Polishing after sanding on request
- Wash-down of the whole area
- Care advice for the first week
- Free inspection and test patch
- Masking of walls, skirting and furniture edges
- Wet sanding through the grit sequence
What each surface needs
| Problem | Wet sanding effect | Outcome |
|---|---|---|
| Grey mop haze | Strips the residue layer | True stone colour returns |
| Old wax and coatings | Fully removed | Surface ready for polish |
| Light scratches | Ground out in stages | Even surface |
| Paint, POP and cement spots | Removed without acid | Clean stone |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free)
- Masking and water containment
- Wet sanding in grit stages
- Slurry vacuumed and area washed
- Handover with finish options
Marble Floor Polishing rates in Delhi
| Work | Guide band | Notes |
|---|---|---|
| Wet sanding only | Rs 5-15 per sq ft | Residue removal |
| Wet sanding plus polishing | Rs 15-25 per sq ft | Dull floors |
| Sanding, grinding and polish | Rs 25-35 per sq ft | Damage and lippage |
| Coating after sanding | Quoted after inspection | Protection |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving Siri Fort Delhi
Marble Floor Polishing in Siri Fort Delhi is handled on scheduled routes by our Delhi team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for Siri Fort Delhi addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own Siri Fort Delhi job handed over for your records
Buff or full polish? A straight answer
| Condition of the floor | Correct job | Why |
|---|---|---|
| Dull but even, no scratches | Buff only | Surface is sound, only the sheen is lost |
| Light scratches and lane wear | Diamond polish | Surface layer needs refining |
| Visible lippage or deep scratches | Grinding plus polish | Buffing cannot level stone |
| Wax or polish residue build-up | Strip, then polish | New finish will not bond over residue |
Buffing is the cheaper option and we will tell you when it is enough. Selling a full polish for a floor that only needed a buff is how a contractor gets a bad name.
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Machines are matched to the job. A 400 mm single-disc machine for open floors, edge machines for skirtings and staircases, and hand blocks for corners and thresholds where a machine cannot safely reach.
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
Why clients book us
- Wet method keeps dust out of the house
- Slurry contained and vacuumed, not left to dry
- Test patch shown before the full job
- One team for sanding, grinding and polishing
Serving Delhi and nearby areas
The Delhi team operates out of Badarpur, close to the Mathura Road corridor and South Delhi. Delhi floors take a beating from dust, metro-era construction grit and hard water. Makrana, Katni and Kota dominate older colonies, while newer builder floors use imported marble. Inspections are booked within 24-48 hours and most flats are finished the same day. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
Does wet sanding remove a lot of stone?
It removes the coating and the damaged top layer only. Deep lippage needs grinding first, which we identify during inspection.
How messy is it?
We mask surfaces and vacuum slurry as we work, then wash the area before handover. Your furniture and curtains do not end up coated in dust.
Can it be done room by room?
Yes. Most clients do one or two rooms at a time, and dry paths are kept so the house stays usable.
Why wet sanding instead of dry?
Because dust control matters in occupied homes. Water carries the residue away and keeps the surface cool, which protects the stone from heat marks.
Do you cover Siri Fort Delhi?
Yes. Siri Fort Delhi is on our regular route with the Delhi team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in Siri Fort Delhi?
Inspection first, then scheduling. Most Siri Fort Delhi jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
How do I know if buffing is enough?
If the floor is evenly dull with no visible scratch pattern, a buff usually restores it. If you can see lanes, scratches or a step between slabs, it needs polishing or grinding, and we show you why on a test patch.
Is buffing a waste of money then?
Not at all. It is the correct maintenance step for a sound floor and costs a fraction of a full job. It becomes a waste only when the surface damage needs something deeper.
Can you do a test patch first?
Yes, on every job. One tile or a corner, so you judge the actual result before committing to the whole floor.