Marble Floor Polishing in Karunamoyee
Marble does not fade evenly. Doorways, kitchen entries and stair landings wear first, which is why floors start looking patchy. We polish the whole surface back to one uniform gloss so no room looks newer than the rest. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Free inspection of porosity and stain history
- Deep cleaning before sealing (sealer over dirt seals dirt)
- Drying time allowed, no sealing on damp stone
- Impregnating sealer applied evenly
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Free inspection of porosity and stain history
- Deep cleaning before sealing (sealer over dirt seals dirt)
- Drying time allowed, no sealing on damp stone
- Impregnating sealer applied evenly
- Second coat on high-absorption stone
- Buffer and residue removal
- Wet-area and kitchen priority treatment
- Maintenance and re-seal schedule explained
What each surface needs
| Stone | Absorption | Seal priority |
|---|---|---|
| Marble | Medium, acid and oil sensitive | Kitchens, entries, washbasins |
| Limestone | High | All wet areas |
| Granite | Low | Kitchen platforms, stairs |
| Travertine | High, pitted | Bathrooms, outdoors |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and porosity test (free)
- Deep cleaning and residue removal
- Full drying of the stone surface
- Sealer applied in even coats
- Buffing, handover and re-seal schedule
Marble Floor Polishing rates in Kolkata
| Work | Guide band | Notes |
|---|---|---|
| Clean and seal | Rs 5-15 per sq ft | Dry floors and walls |
| Strip, clean and seal | Rs 15-25 per sq ft | Old coating present |
| High-absorption stone, two coats | Quoted after inspection | Limestone and travertine |
| Re-seal cycle | Per sq ft | Every 12-24 months |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving Karunamoyee
Marble Floor Polishing in Karunamoyee is handled on scheduled routes by our Kolkata team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for Karunamoyee addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own Karunamoyee job handed over for your records
Marble and granite need different treatment
| Marble | Granite | |
|---|---|---|
| Hardness | Softer, scratches more visibly | Harder, resists scratches |
| Acid | Etches immediately, never use | Dulls the surface, avoid |
| Finishing | Diamond pads up to 3000 grit | Its own pad set and compounds |
| Typical aftercare | Sealer every 12-24 months | Sealer on kitchen and stairs |
| Gloss achievable | Very high on hard whites | Deep lustre, not mirror |
We keep separate pad sets and compounds for each, because using marble products on granite (or the reverse) is the fastest way to end up with a hazy surface.
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Machines are matched to the job. A 400 mm single-disc machine for open floors, edge machines for skirtings and staircases, and hand blocks for corners and thresholds where a machine cannot safely reach.
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
Why clients book us
- Sealer applied only on clean, dry stone
- Impregnating sealers used, not film coatings
- Honest about what sealing does and does not do
- Re-seal cycle scheduled so protection never lapses
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
Will sealing make my marble stain-proof?
No, and any contractor saying that is overselling. Sealing buys you time to wipe a spill. Lemon juice or oil left overnight can still mark sealed stone.
How often should stone be re-sealed?
Every twelve to twenty-four months for working areas like kitchens, entries and washbasins. Dry bedroom floors and walls hold sealer much longer.
Can sealer be applied over an old polish?
No. It will not bond, and it traps the old residue underneath. Cleaning or stripping first is part of the job, not an optional extra.
Does sealing change the colour?
Impregnating sealers are colourless. If a sealer darkens the stone, it is a film-forming product rather than an impregnator, which is a different finish choice.
Do you cover Karunamoyee?
Yes. Karunamoyee is on our regular route with the Kolkata team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in Karunamoyee?
Inspection first, then scheduling. Most Karunamoyee jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
Can you polish a floor that mixes marble and granite?
Yes, and it is common in lobbies and staircases. Each surface is polished to a matching level of sheen rather than the same pad sequence, so the two read as one floor.
Is granite easier to maintain than marble?
It is less acid-sensitive and harder, so it stains and scratches less. It still dulls from repeated wrong cleaning, and it still needs sealing in wet or greasy areas.
Why does marble etch while granite does not?
Marble is calcium-based, so acid dissolves the surface and leaves a white mark. Granite is silicate-based and resists acid better, though strong acid still dulls its polish.