Marble Floor Polishing in Kamdahari
Marble does not fade evenly. Doorways, kitchen entries and stair landings wear first, which is why floors start looking patchy. We polish the whole surface back to one uniform gloss so no room looks newer than the rest. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit.
- Free inspection measuring lippage and slab thickness
- Tapping test for hollow slabs
- Wet grinding to keep dust down indoors
- Coarse to fine grit sequence with no skipped stages
At a glance
- Diamond polishing
- Stain removal
- Rate locked in writing
A real before and after photo is added here for the strongest result.
What is included in marble floor polishing
- Wet grinding to keep dust down indoors
- Coarse to fine grit sequence with no skipped stages
- Slurry contained and vacuumed as we work
- Refining passes to remove grind marks
- Polishing to follow on the same job
- Wash-down and walkthrough
- Free inspection measuring lippage and slab thickness
- Tapping test for hollow slabs
What each surface needs
| Problem | What grinding does | Outcome |
|---|---|---|
| Lippage between slabs | Cuts the high slab to floor level | Flat floor, no trip lines |
| Dark traffic lanes | Removes the compacted worn layer | Uniform colour across the room |
| Deep scratches and gouges | Cuts back below the scratch depth | Gone, or faint on very deep damage |
| Cement, POP and paint splatter | Removes it without acid | Clean stone, no chemical risk |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection, lippage measurement and hollow test (free)
- Masking of walls, skirting, doors and furniture
- Coarse grinding, 40-60 minutes per 100 sq ft
- Refining at 200 and 400 grit, 30-45 minutes per 100 sq ft
- Polishing, wash-down and handover
Marble Floor Polishing rates in Kolkata
| Work | Guide band | Typical case |
|---|---|---|
| Light grinding with polish | Rs 15-25 per sq ft | Surface damage, patchy gloss |
| Full grinding, levelling and polish | Rs 25-35 per sq ft | Lippage, deep damage, dark lanes |
| Crystallisation after grinding | Quoted after inspection | Adds hardness and gloss |
| Grinding plus slab re-laying | Quoted per slab | Hollow or lifted slabs |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving Kamdahari
Marble Floor Polishing in Kamdahari is handled on scheduled routes by our Kolkata team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for Kamdahari addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own Kamdahari job handed over for your records
Marble and granite need different treatment
| Marble | Granite | |
|---|---|---|
| Hardness | Softer, scratches more visibly | Harder, resists scratches |
| Acid | Etches immediately, never use | Dulls the surface, avoid |
| Finishing | Diamond pads up to 3000 grit | Its own pad set and compounds |
| Typical aftercare | Sealer every 12-24 months | Sealer on kitchen and stairs |
| Gloss achievable | Very high on hard whites | Deep lustre, not mirror |
We keep separate pad sets and compounds for each, because using marble products on granite (or the reverse) is the fastest way to end up with a hazy surface.
Payment terms are stated upfront: advances apply only where material has to be bought for a large job, and the balance is settled after the walkthrough so you are never paying for work you have not seen.
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Weight and load matter on upper floors and terraces. Where a slab has been laid over a void or a lightweight screed, we reduce machine weight and speed rather than risk cracking the base.
Why clients book us
- Wet grinding with slurry contained and the site washed down
- Same team polishes after grinding, so nothing is blamed on another contractor
- Hollow and thin slabs flagged honestly instead of ground
- 12 years of stone grinding
Serving Kolkata and nearby areas
Kolkata jobs are scheduled as a fixed visit batch so the crew and machines travel together and travel cost is not loaded onto your rate. Kolkata buildings are older and often mix marble, Kota and mosaic in the same flat, with high humidity and monsoon damp that dulls floors faster than in Delhi. Salt-laden air near the river also leaves a film that looks like stone wear but is surface deposit. Inspections are booked within 24-48 hours and most jobs take 1-2 days per flat. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Floor Polishing - common questions
Does grinding create dust all over the house?
We grind wet, so dust becomes slurry rather than airborne powder, and we mask doors and skirting. Slurry is vacuumed and washed before we leave.
Can lippage between marble and tile be levelled?
Usually yes where the two surfaces meet at different heights. Where the step is more than a few millimetres, an exact match may not be possible and we say so before starting.
Is grinding always followed by polishing?
Yes in practice. Grinding leaves machine marks until the finer grits and polishing smooth them out, which is why the two stages are quoted together.
What if a slab is hollow?
Grinding cannot re-bond it. Loose slabs must be re-laid, and we quote that separately rather than hiding the problem under a polish.
Will grinding make my floor noticeably thinner?
It removes a fraction of a millimetre at the surface and more only where slabs are high. Average floors take several grinding cycles over their life. We measure thickness during the free inspection first.
Do you cover Kamdahari?
Yes. Kamdahari is on our regular route with the Kolkata team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in Kamdahari?
Inspection first, then scheduling. Most Kamdahari jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
Can you polish a floor that mixes marble and granite?
Yes, and it is common in lobbies and staircases. Each surface is polished to a matching level of sheen rather than the same pad sequence, so the two read as one floor.
Is granite easier to maintain than marble?
It is less acid-sensitive and harder, so it stains and scratches less. It still dulls from repeated wrong cleaning, and it still needs sealing in wet or greasy areas.
Why does marble etch while granite does not?
Marble is calcium-based, so acid dissolves the surface and leaves a white mark. Granite is silicate-based and resists acid better, though strong acid still dulls its polish.