Diamond Marble Polishing in Kamla Nagar
Diamond polishing cuts the stone with graded diamond pads, so the shine comes out of the marble instead of sitting on top of it. That is the difference between a floor that still looks good after a year and one that goes patchy in three months, the way wax does. Work in Kamla Nagar is planned as a scheduled visit: the crew and machines travel together on a fixed date, and the rate is written down after the floor is seen in person or from clear photos.
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
- Coarse diamond passes for scratches and lippage
- Progressive grits to remove every previous scratch pattern
At a glance
- 60-3000 grit
- No wax finish
- Klindex machines
A real before and after photo is added here for the strongest result.
What is included in diamond marble polishing
- Coarse diamond passes for scratches and lippage
- Progressive grits to remove every previous scratch pattern
- Fine polishing to bring up the working gloss
- Edge and corner work by hand machine
- Optional crystallisation or nano finish
- Floor washed and handed over with a gloss check
- Gloss reading and damage mapping before we quote
- Masking of walls, skirting and furniture edges
What each surface needs
| Grit | What it does | When it is needed |
|---|---|---|
| 60 and 100 | Cuts back lippage, deep scratches and rough patches | Uneven joints, heavy damage |
| 200 and 400 | Removes grinding marks, levels the surface | After any coarse stage |
| 800 | Closes the pores and prepares the stone | Almost every job |
| 1500 and 3000 | Working gloss and final mirror pass | Homes, lobbies, showrooms |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free, 20 minutes)
- Masking of all surfaces that should not get slurry
- Sequential diamond passes, 30-45 minutes per 100 sq ft
- Finishing pass at 1500 or 3000 grit, coating if you approve
- Handover with before and after gloss comparison
Diamond Marble Polishing rates in Kamla Nagar
| Work | Guide band | Where it applies |
|---|---|---|
| Light diamond pass | Rs 5-15 per sq ft | Sound floors, mild dulling |
| Standard diamond polishing | Rs 15-25 per sq ft | Scratch lanes, worn gloss |
| Deep diamond plus crystallisation | Rs 25-35 per sq ft | Lippage, stains, heavy wear |
| Coating after polishing | Quoted after inspection | Silicate, epoxy or nano |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Marble and granite need different treatment
| Marble | Granite | |
|---|---|---|
| Hardness | Softer, scratches more visibly | Harder, resists scratches |
| Acid | Etches immediately, never use | Dulls the surface, avoid |
| Finishing | Diamond pads up to 3000 grit | Its own pad set and compounds |
| Typical aftercare | Sealer every 12-24 months | Sealer on kitchen and stairs |
| Gloss achievable | Very high on hard whites | Deep lustre, not mirror |
We keep separate pad sets and compounds for each, because using marble products on granite (or the reverse) is the fastest way to end up with a hazy surface.
Nothing is hidden behind a shine. Where a surface has damage that polishing cannot correct, we mark it during inspection and put it in writing, so expectations are set before work starts rather than argued over afterwards.
Where a floor has mixed surfaces, each one gets its own pad sequence and compound. Treating Kota stone and imported marble with the same approach is how floors get patchy.
Protection is planned, not improvised. Furniture is moved to one side and covered, curtain hems are lifted, and a walking route is kept clear throughout so the household can still move around.
Why clients book us
- Fresh diamond segments, because worn pads leave swirl marks
- Correct pad set per stone: marble, granite, Kota, terrazzo
- One contractor for grinding, polishing and coatings
- Gloss checked with you before the crew leaves
Serving Kamla Nagar and nearby areas
Kamla Nagar jobs are booked as a fixed visit batch, so travel is planned into the date instead of being added as a surprise. Work in Kamla Nagar is planned as a scheduled visit: the crew and machines travel together on a fixed date, and the rate is written down after the floor is seen in person or from clear photos. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Diamond Marble Polishing - common questions
How much marble does it remove?
Microns, not visible layers. Even a full sequence on a damaged floor only corrects the worn top surface; coarse grinding is the stage that removes more and we only use it when needed.
How glossy will the floor look?
Most marble reaches a near-mirror gloss. Statuario and Makrana take a very high gloss, while honed travertine and some Kota floors look better satin. We agree the target before starting.
How long does the finish last?
Two to three years in homes before a light maintenance pass; eight to twelve months in offices and hotels, longer with a silicate or nano coating.
Can it be done in an occupied home?
Yes. The process is wet, so dust stays low. We work room by room and leave dry paths so you can stay in the house.
How is diamond polishing different from the polish my housekeeping does?
Housekeeping applies cream or wax that sits on the surface and wears off in walking lanes within weeks. Diamond polishing refines the stone itself, so the finish is part of the floor.
Can you polish a floor that mixes marble and granite?
Yes, and it is common in lobbies and staircases. Each surface is polished to a matching level of sheen rather than the same pad sequence, so the two read as one floor.
Is granite easier to maintain than marble?
It is less acid-sensitive and harder, so it stains and scratches less. It still dulls from repeated wrong cleaning, and it still needs sealing in wet or greasy areas.
Why does marble etch while granite does not?
Marble is calcium-based, so acid dissolves the surface and leaves a white mark. Granite is silicate-based and resists acid better, though strong acid still dulls its polish.