Tiles Polishing in Delhi NCR
Most tile floors in Delhi NCR look dull because the protective factory sheen has worn through in walking routes. We clean the surface properly, then refine it so the tile reads evenly again. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Free inspection and test patch
- Masking of walls, skirting and furniture edges
- Wet sanding through the grit sequence
- Slurry vacuumed as work proceeds
At a glance
- Vitrified & ceramic
- Grout cleaned too
- Anti-skid safe
A real before and after photo is added here for the strongest result.
What is included in tiles polishing service price
- Free inspection and test patch
- Masking of walls, skirting and furniture edges
- Wet sanding through the grit sequence
- Slurry vacuumed as work proceeds
- Damage and joint treatment where found
- Polishing after sanding on request
- Wash-down of the whole area
- Care advice for the first week
What each surface needs
| Problem | Wet sanding effect | Outcome |
|---|---|---|
| Grey mop haze | Strips the residue layer | True stone colour returns |
| Old wax and coatings | Fully removed | Surface ready for polish |
| Light scratches | Ground out in stages | Even surface |
| Paint, POP and cement spots | Removed without acid | Clean stone |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free)
- Masking and water containment
- Wet sanding in grit stages
- Slurry vacuumed and area washed
- Handover with finish options
Tiles Polishing Service Price rates in Delhi NCR
| Work | Guide band | Notes |
|---|---|---|
| Wet sanding only | Rs 5-15 per sq ft | Residue removal |
| Wet sanding plus polishing | Rs 15-25 per sq ft | Dull floors |
| Sanding, grinding and polish | Rs 25-35 per sq ft | Damage and lippage |
| Coating after sanding | Quoted after inspection | Protection |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
What changes the price for tiles polishing service price in Delhi NCR
| Factor | Effect on rate | What to expect |
|---|---|---|
| Total area | Bigger areas cost less per sq ft | Slab rates above 1,000 sq ft |
| Damage depth | Grinding raises the rate | Decided by the test patch |
| Stone type | Imported and filled slabs take longer | See the surface table |
| Access | Upper floors and corners take longer | Confirmed before booking |
Ask for one written rate per surface. A single number for the whole house without an inspection always changes later.
Marble and granite need different treatment
| Marble | Granite | |
|---|---|---|
| Hardness | Softer, scratches more visibly | Harder, resists scratches |
| Acid | Etches immediately, never use | Dulls the surface, avoid |
| Finishing | Diamond pads up to 3000 grit | Its own pad set and compounds |
| Typical aftercare | Sealer every 12-24 months | Sealer on kitchen and stairs |
| Gloss achievable | Very high on hard whites | Deep lustre, not mirror |
We keep separate pad sets and compounds for each, because using marble products on granite (or the reverse) is the fastest way to end up with a hazy surface.
Nothing is hidden behind a shine. Where a surface has damage that polishing cannot correct, we mark it during inspection and put it in writing, so expectations are set before work starts rather than argued over afterwards.
Where a floor has mixed surfaces, each one gets its own pad sequence and compound. Treating Kota stone and imported marble with the same approach is how floors get patchy.
Protection is planned, not improvised. Furniture is moved to one side and covered, curtain hems are lifted, and a walking route is kept clear throughout so the household can still move around.
Why clients book us
- Test patch shown before the full job
- One team for sanding, grinding and polishing
- 12 years of marble work in Delhi NCR
- Wet method keeps dust out of the house
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Tiles Polishing Service Price - common questions
Why wet sanding instead of dry?
Because dust control matters in occupied homes. Water carries the residue away and keeps the surface cool, which protects the stone from heat marks.
Does wet sanding remove a lot of stone?
It removes the coating and the damaged top layer only. Deep lippage needs grinding first, which we identify during inspection.
How messy is it?
We mask surfaces and vacuum slurry as we work, then wash the area before handover. Your furniture and curtains do not end up coated in dust.
Can it be done room by room?
Yes. Most clients do one or two rooms at a time, and dry paths are kept so the house stays usable.
Is the price negotiable?
The rate per sq ft is not inflated to leave room for haggling. We scope honestly: if the floor needs only a buff, we quote a buff instead of a full diamond job, and tell you when the cheaper option will hold.
Do you take advance payment?
The package is confirmed in writing first. Advance for material is normal on large jobs; the balance is settled after the walkthrough.
Can you polish a floor that mixes marble and granite?
Yes, and it is common in lobbies and staircases. Each surface is polished to a matching level of sheen rather than the same pad sequence, so the two read as one floor.
Is granite easier to maintain than marble?
It is less acid-sensitive and harder, so it stains and scratches less. It still dulls from repeated wrong cleaning, and it still needs sealing in wet or greasy areas.
Why does marble etch while granite does not?
Marble is calcium-based, so acid dissolves the surface and leaves a white mark. Granite is silicate-based and resists acid better, though strong acid still dulls its polish.