Shower Tile Polishing in Delhi NCR
Vitrified, ceramic and porcelain tiles do not fade, but the surface does. Fine scratches and cleaning residue build up into a grey haze that no amount of mopping removes, and that is what tile polishing corrects. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Free inspection of porosity and stain history
- Deep cleaning before sealing (sealer over dirt seals dirt)
- Drying time allowed, no sealing on damp stone
- Impregnating sealer applied evenly
At a glance
- Vitrified & ceramic
- Grout cleaned too
- Anti-skid safe
A real before and after photo is added here for the strongest result.
What is included in shower tile polishing
- Deep cleaning before sealing (sealer over dirt seals dirt)
- Drying time allowed, no sealing on damp stone
- Impregnating sealer applied evenly
- Second coat on high-absorption stone
- Buffer and residue removal
- Wet-area and kitchen priority treatment
- Maintenance and re-seal schedule explained
- Free inspection of porosity and stain history
What each surface needs
| Stone | Absorption | Seal priority |
|---|---|---|
| Marble | Medium, acid and oil sensitive | Kitchens, entries, washbasins |
| Limestone | High | All wet areas |
| Granite | Low | Kitchen platforms, stairs |
| Travertine | High, pitted | Bathrooms, outdoors |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and porosity test (free)
- Deep cleaning and residue removal
- Full drying of the stone surface
- Sealer applied in even coats
- Buffing, handover and re-seal schedule
Shower Tile Polishing rates in Delhi NCR
| Work | Guide band | Notes |
|---|---|---|
| Clean and seal | Rs 5-15 per sq ft | Dry floors and walls |
| Strip, clean and seal | Rs 15-25 per sq ft | Old coating present |
| High-absorption stone, two coats | Quoted after inspection | Limestone and travertine |
| Re-seal cycle | Per sq ft | Every 12-24 months |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
The process, step by step
- Site inspection, gloss reading and hidden test patch
- Masking of skirting, fittings, doors and furniture edges
- Residue and old polish stripping where present
- Grinding if lippage or deep damage is found
- Progressive polishing through the grit sequence
- Optional silicate, crystallisation, epoxy or nano finish
- Edge and corner hand work
- Wash-down, walkthrough and care guidance
Each stage is completed on the whole area before the next one starts, so the floor never ends up with a bright patch next to an unfinished section.
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Machines are matched to the job. A 400 mm single-disc machine for open floors, edge machines for skirtings and staircases, and hand blocks for corners and thresholds where a machine cannot safely reach.
Team composition is consistent: a supervisor plus two machine operators on standard jobs, with additional hands for staircases, multiple floors or tight access. The same supervisor stays with the job start to finish.
Why clients book us
- Sealer applied only on clean, dry stone
- Impregnating sealers used, not film coatings
- Honest about what sealing does and does not do
- Re-seal cycle scheduled so protection never lapses
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Shower Tile Polishing - common questions
Will sealing make my marble stain-proof?
No, and any contractor saying that is overselling. Sealing buys you time to wipe a spill. Lemon juice or oil left overnight can still mark sealed stone.
How often should stone be re-sealed?
Every twelve to twenty-four months for working areas like kitchens, entries and washbasins. Dry bedroom floors and walls hold sealer much longer.
Can sealer be applied over an old polish?
No. It will not bond, and it traps the old residue underneath. Cleaning or stripping first is part of the job, not an optional extra.
Does sealing change the colour?
Impregnating sealers are colourless. If a sealer darkens the stone, it is a film-forming product rather than an impregnator, which is a different finish choice.
How long does each step take?
As a guide, preparation is under an hour, grinding runs 25-40 minutes per 100 sq ft, polishing 15-25 minutes, and finishing plus clean-up about an hour. Bigger areas are scheduled over more days.
Can steps be skipped to save money?
Not safely. Skipping grit stages is the most common shortcut and shows up as scratch haze within weeks. If you want to reduce cost, reduce the area covered this cycle, not the process.
Do you work in one room or the whole floor at a time?
Room by room if you are living in, whole floor if the house is empty, which produces a more even finish because lighting and drying are consistent.