Tile Mortar Removal Tile Mortar and Cement Removal in Delhi NCR
Acid is the shortcut most contractors use, and it is what dulls tile faces and etches stone permanently. We remove mortar mechanically and with pH-neutral products instead. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit.
- Free inspection of the film and its depth
- Masking of skirting, fittings and adjacent surfaces
- Mechanical removal of mortar and cement film
- pH-neutral cleaning, no acid on stone
At a glance
- 12 years experience
- 600+ projects a year
- Written rates
A real before and after photo is added here for the strongest result.
What is included in tile mortar removal
- Mechanical removal of mortar and cement film
- pH-neutral cleaning, no acid on stone
- Scrubbing of grout lines and edges
- Tile surface refining after removal
- Full wash-down and disposal
- Handover with care advice
- Free inspection of the film and its depth
- Masking of skirting, fittings and adjacent surfaces
What each surface needs
| Deposit | Cause | Removal method |
|---|---|---|
| Cement film | Grouting and slab work | Mechanical and neutral clean |
| Mortar haze | Laying residue | Scrub and refine |
| POP and paint splatter | Finishing work | Scrape and dissolve |
| Grout residue in joints | Grouting | Joint scrubbing |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and test patch (free)
- Protection of walls and fittings
- Mechanical removal of deposits
- Neutral cleaning and joint scrubbing
- Wash-down and handover
Tile Mortar Removal rates in Delhi NCR
| Work | Guide band | Notes |
|---|---|---|
| Cement film removal | Rs 5-15 per sq ft | Post-construction floors |
| Mortar removal with refining | Rs 15-25 per sq ft | Haze and residue |
| POP and paint removal | Per patch or per sq ft | Stubborn splatter |
| Sealing after removal | Quoted after inspection | Optional protection |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
The process, step by step
- Site inspection, gloss reading and hidden test patch
- Masking of skirting, fittings, doors and furniture edges
- Residue and old polish stripping where present
- Grinding if lippage or deep damage is found
- Progressive polishing through the grit sequence
- Optional silicate, crystallisation, epoxy or nano finish
- Edge and corner hand work
- Wash-down, walkthrough and care guidance
Each stage is completed on the whole area before the next one starts, so the floor never ends up with a bright patch next to an unfinished section.
After-care guidance is handed over in writing: which cleaner to use, how to mop, and what to avoid during the first week. Most repeat problems trace back to cleaning products rather than the work itself.
Every job ends with a walkthrough. You see the gloss reading, the treated patches and the joints before the crew packs up, and the same crew owns any correction needed later.
Why clients book us
- No acid on stone, because acid damage is permanent
- Mechanical removal before any chemical
- Slurry and waste cleared from site
- Test patch shown before full commitment
Serving Delhi NCR and nearby areas
Our Badarpur (Mathura Road) and Gurgaon (Badshahpur, Sector 48) teams cover the whole NCR belt. Delhi NCR mixes very old housing stock with new high-rise towers, so a single visit can mean Kota stone in one room and Italian marble in the next. We carry pads for both and quote each surface on its own merit. Inspections are booked within 24-48 hours and most jobs take 1-2 days. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Tile Mortar Removal - common questions
Why not just use acid to remove the cement film?
Because acid attacks the tile and stone as well as the cement. It dulls vitrified tile faces and etches marble, and the damage shows up months later. Mechanical removal costs more time but does not damage the floor.
Can you remove film from a floor laid years ago?
Usually yes, if the film was never polished over. If a previous contractor sealed the residue under a coating, the coating has to be stripped first, and we tell you that after testing a patch.
Is the process dusty?
We work wet and vacuum as we go, and we mask adjoining surfaces. Slurry is cleared before handover.
Do you also clean the grout after construction?
Yes. Joint scrubbing is included, because mortar dust sits in the grout lines and reappears otherwise.
How long does each step take?
As a guide, preparation is under an hour, grinding runs 25-40 minutes per 100 sq ft, polishing 15-25 minutes, and finishing plus clean-up about an hour. Bigger areas are scheduled over more days.
Can steps be skipped to save money?
Not safely. Skipping grit stages is the most common shortcut and shows up as scratch haze within weeks. If you want to reduce cost, reduce the area covered this cycle, not the process.
Do you work in one room or the whole floor at a time?
Room by room if you are living in, whole floor if the house is empty, which produces a more even finish because lighting and drying are consistent.