Marble Polishing Stone Floor Cleaning and Polishing in New Delhi
Cleaning and polishing are two different jobs. A floor can be clean and still look grey because the sheen is gone, and it can be shiny and still be dirty if residue has been sealed in. We do both, in the right order. Delhi floors take a beating from dust, metro-era construction grit and hard water. Makrana, Katni and Kota dominate older colonies, while newer builder floors use imported marble.
- Free inspection with a residue test on a hidden patch
- Masking and protection of adjacent surfaces
- Residue and soap film stripping with pH-neutral products
- Deep cleaning of joints and edges
At a glance
- pH-neutral products
- Residue stripping
- Polishing included
A real before and after photo is added here for the strongest result.
What is included in marble polishing
- Free inspection with a residue test on a hidden patch
- Masking and protection of adjacent surfaces
- Residue and soap film stripping with pH-neutral products
- Deep cleaning of joints and edges
- Polishing to restore the surface sheen
- Stain treatment for oil, rust and hard water
- Sealing or coating option
- Wash-down and handover
What each surface needs
| Problem | Cause | Fix |
|---|---|---|
| Grey haze after mopping | Cleaning residue and soap film | Strip, then polish |
| White patches | Hard water and acid contact | pH-neutral clean, fine polish |
| Dark spots and rings | Oil, rust or planters | Poultice, then polish |
| Patchy gloss | Uneven earlier polishing | Grind and polish to one level |
Every surface is tested on a hidden patch before work starts, so you see the result before committing to the whole floor.
How the job runs
- Inspection and residue test (free)
- Masking and preparation
- Stripping of residue and old polish
- Polishing to restore the sheen
- Sealing option and handover
Marble Polishing rates in Delhi
| Work | Guide band | Notes |
|---|---|---|
| Deep cleaning and stripping | Rs 5-15 per sq ft | Residue and film removal |
| Cleaning plus polishing | Rs 15-25 per sq ft | Dull but sound floors |
| Deep clean with grinding | Rs 25-35 per sq ft | Heavy wear and stains |
| Sealing or coating | Quoted after inspection | Wet and high-traffic areas |
Rates depend on surface type, damage depth, area and access. The figure is written down before work begins.
Serving New Delhi
Marble Polishing in New Delhi is handled on scheduled routes by our Delhi team, so travel is planned rather than added as a surprise.
- Site inspection booked within 24-48 hours for New Delhi addresses
- Society gate, lift and parking permissions coordinated before the crew arrives
- Water point, power and work area confirmed at the time of booking
- Slurry and waste removed the same day, never dumped in the society bins
- Before-and-after photographs of your own New Delhi job handed over for your records
The process, step by step
- Site inspection, gloss reading and hidden test patch
- Masking of skirting, fittings, doors and furniture edges
- Residue and old polish stripping where present
- Grinding if lippage or deep damage is found
- Progressive polishing through the grit sequence
- Optional silicate, crystallisation, epoxy or nano finish
- Edge and corner hand work
- Wash-down, walkthrough and care guidance
Each stage is completed on the whole area before the next one starts, so the floor never ends up with a bright patch next to an unfinished section.
Old polish, wax and cleaning residue are stripped before any new finish goes on. Layering a fresh treatment over residue is what makes floors look grey again within weeks.
Dust and water control is planned before we start: masking on skirting and fittings, wet working instead of dry, and slurry vacuumed as the machine moves rather than left to dry in corners.
Why clients book us
- pH-neutral products used on all calcite stone
- Residue stripped before sealing so nothing is trapped
- Test patch shown before full commitment
- One team for cleaning, polishing and sealing
Serving Delhi and nearby areas
The Delhi team operates out of Badarpur, close to the Mathura Road corridor and South Delhi. Delhi floors take a beating from dust, metro-era construction grit and hard water. Makrana, Katni and Kota dominate older colonies, while newer builder floors use imported marble. Inspections are booked within 24-48 hours and most flats are finished the same day. Call 86070 01043 or WhatsApp photos of your floor for an indicative rate.
Marble Polishing - common questions
Is deep cleaning enough without polishing?
It restores cleanliness but not sheen. If the surface has micro-scratches and worn gloss, cleaning alone will still look grey, and polishing is needed.
Which cleaner should we use afterwards?
A pH-neutral stone cleaner with clean water. Acidic and abrasive products damage polished stone surfaces within a few uses.
How often should stone floors be deep cleaned?
Every six to twelve months for homes and every three to six months in commercial spaces, depending on footfall and cleaning method.
Why does my floor look dull right after mopping?
Because you are looking at cleaning residue and soap film, not the stone. Mopping with the wrong product keeps adding a layer. Stripping it and polishing the surface is what brings the colour back.
Do you cover New Delhi?
Yes. New Delhi is on our regular route with the Delhi team, and inspections there are usually booked within 24-48 hours. For larger areas we schedule a fixed route day so travel cost is shared.
How soon can work start in New Delhi?
Inspection first, then scheduling. Most New Delhi jobs begin within a week of approval, and single-room works are often earlier if you are flexible on the date.
How long does each step take?
As a guide, preparation is under an hour, grinding runs 25-40 minutes per 100 sq ft, polishing 15-25 minutes, and finishing plus clean-up about an hour. Bigger areas are scheduled over more days.
Can steps be skipped to save money?
Not safely. Skipping grit stages is the most common shortcut and shows up as scratch haze within weeks. If you want to reduce cost, reduce the area covered this cycle, not the process.
Do you work in one room or the whole floor at a time?
Room by room if you are living in, whole floor if the house is empty, which produces a more even finish because lighting and drying are consistent.